Subject: | |
From: | |
Reply To: | DesignerCouncil E-Mail Forum. |
Date: | Thu, 26 Mar 1998 08:33:53 -0500 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Double Ditto.
I tried using the gerber 274X format in Version 2.0 of PowerPCB and was
also unable to read it into Gerbtool. I too have gone back to the 274D
format.
PADS are you listening ? Where's QA in times like this ?
>
>Regards, Greg.
Gregory E. Bordash,
Senior Technologist PCB Design
ATI Technologies Inc.,
33 Commerce Valley Drive East,
Thornhill, Ontario, Canada, L3T 7N6
Phone:(905) 882-2600 ext: 8370, Fax: (905) 882-9339
Email: [log in to unmask]
>----------
>From: George Uptain[SMTP:[log in to unmask]]
>Sent: Thursday, March 26, 1998 7:19 AM
>To: [log in to unmask]
>Subject: Re: [DC] PADS Gerber Output Question
>
>Ditto. I use Pads PowerPCB and must output in D then let CAM350 output
>the X gerber files.
>George W Uptain, Jr.
>Austin Product Center of Schlumberger Oilfield Services
>(512)331-3183
>
>> -----Original Message-----
>> From: Ralph Garvin [SMTP:[log in to unmask]]
>> Sent: Wednesday, March 25, 1998 7:54 PM
>> To: [log in to unmask]
>> Subject: Re: [DC] PADS Gerber Output Question
>>
>> Steve,
>> The PADS 274x output is terrible. We have many problems with it and
>> try it first with our viewer[CAM350] before sending it to the pcb
>> production houses.[They also have had many problems with the files].
>> Just make sure of your 274D format setting to get the correct number
>> of
>> digits.
>> You would think that something as simple as the gerber output
>> module
>> would work correctly!!!!!
>>
>> Good Luck,
>>
>> Ralph Garvin
>>
>> ################################################################
>> DesignerCouncil E-Mail Forum provided as a free service by IPC using
>> LISTSERV 1.8c
>> ################################################################
>> To subscribe/unsubscribe, send a message to [log in to unmask] with
>> following text in the body:
>> To subscribe: SUBSCRIBE DesignerCouncil <your full name>
>> To unsubscribe: SIGNOFF DesignerCouncil
>> ################################################################
>> Please visit IPC web site (http://jefry.ipc.org/forum.htm) for
>> additional information.
>> For the technical support contact Dmitriy Sklyar at [log in to unmask] or
>> 847-509-9700 ext.311
>> ################################################################
>
>################################################################
>DesignerCouncil E-Mail Forum provided as a free service by IPC using LISTSERV
>1.8c
>################################################################
>To subscribe/unsubscribe, send a message to [log in to unmask] with following
>text in the body:
>To subscribe: SUBSCRIBE DesignerCouncil <your full name>
>To unsubscribe: SIGNOFF DesignerCouncil
>################################################################
>Please visit IPC web site (http://jefry.ipc.org/forum.htm) for additional
>information.
>For the technical support contact Dmitriy Sklyar at [log in to unmask] or
>847-509-9700 ext.311
>################################################################
>
>
################################################################
DesignerCouncil E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe: SUBSCRIBE DesignerCouncil <your full name>
To unsubscribe: SIGNOFF DesignerCouncil
################################################################
Please visit IPC web site (http://jefry.ipc.org/forum.htm) for additional information.
For the technical support contact Dmitriy Sklyar at [log in to unmask] or 847-509-9700 ext.311
################################################################
|
|
|