TECHNET Archives

May 2013

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Condense Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Sender:
X-To:
TechNet E-Mail Forum <[log in to unmask]>, Guy Ramsey <[log in to unmask]>
Date:
Wed, 22 May 2013 13:13:18 +0000
Reply-To:
TechNet E-Mail Forum <[log in to unmask]>, Joyce Koo <[log in to unmask]>
Message-ID:
Subject:
From:
Joyce Koo <[log in to unmask]>
MIME-Version:
1.0
In-Reply-To:
<004f01ce56dd$dd116930$97343b90$@com>
Content-Transfer-Encoding:
quoted-printable
Content-Type:
text/plain; charset="us-ascii"
Parts/Attachments:
text/plain (88 lines)
Kevin,
Here my 2 cents: (1) Aero = the real one with vacuum are good, OSP not much of issue (2) Aero that sitting on the soil rotting are bad, you need to either take care at box level (seal it all) or cover the exposed copper (osp finishing the edge of the solder pads usually are not soldered - exposed copper).  If you coat the board, may be not issue so much.  (3) single reflow side is good = you can choose the thinner OSP.  However, the shelf life and storage condition is a bit restricted.  But easy to solder, if you follow the MFG instruction - compare to the thick OSP (4) there are different OSPs, immidazole - ATT's favor, benzotriazole - used to be IBM's flavor for example. Water soluble flux is aggressive, you need to watch your process window.  (5) reflow might be a bit lower than your usual temperature, since it would be wet faster than ImAg I expect... just a guess.  My 1.92 cents.  

Joyce Koo
Researcher
Materials Interconnect Lab
Office: (519) 888-7465 79945
BlackBerry: (226) 220-4760

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Guy Ramsey
Sent: Wednesday, May 22, 2013 7:17 AM
To: [log in to unmask]
Subject: Re: [TN] OSP processing inputs?

Hi Kevin,
I like OSP. When done properly, it solders great. 

The material is not a conductor, but it is easily pierced by a probe. It
might not be good for a test point. Printing solder on the test points
probably makes sense.

As I understand it, Immersion Ag is protected with an OSP as part of the
plating chemistry. So, there is some truth to what you read. However, the
finishes are different. Silver oxide is easily reduced. In my experience the
finish is more forgiving than OSP over copper. And, because it is a plating
process, unlike OSP over copper, you get the assurance that the copper on
the board will accept plating. 

Your process, optimized for ImAg should be fine with OSP.


Guy  


-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Glidden, Kevin
Sent: Tuesday, May 21, 2013 12:39 PM
To: [log in to unmask]
Subject: [TN] OSP processing inputs?

Hi all,

It looks like I will be getting some PCBs with OSP finish on them to process
thru SMT.  I've not yet used this surface finish, so for me there are a lot
of unknowns.
Some background info:
1 The PCBs will be single sided SMT, so I will not have to worry about
solderability of second side reflow.
2 We are using Sn63Pb37, not lead-free.
3 We are using water soluble ORM0 paste and DI water wash only (no chemical)
4 We typically process with ImAg.
5 MIL/AERO target service environment

I have read some that shelf life is reduced to around 6 months and that OSP
covered pads cannot be used as test points and therefore test pads need to
be solder coated.  I've also read some of the conference papers which seem
to indicate corrosion/environmental performance is at least as good as what
we would get with ImAg.

Any other suggestions / caveats ?

Is there an IPC spec for this finish?

Thanks in advance!

Kevin


______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________


______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________

---------------------------------------------------------------------
This transmission (including any attachments) may contain confidential information, privileged material (including material protected by the solicitor-client or other applicable privileges), or constitute non-public information. Any use of this information by anyone other than the intended recipient is prohibited. If you have received this transmission in error, please immediately reply to the sender and delete this information from your system. Use, dissemination, distribution, or reproduction of this transmission by unintended recipients is not authorized and may be unlawful.

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________

ATOM RSS1 RSS2