Received: |
by ipc.org (Smail3.1.28.1 #2)
id m0wK8Sa-000Br9C; Wed, 23 Apr 97 15:16 CDT |
Encoding: |
2898 Text |
Old-Return-Path: |
|
Date: |
Wed, 23 Apr 97 10:56:18 |
Precedence: |
list |
Resent-From: |
|
Resent-Sender: |
|
X-Status: |
|
Status: |
O |
X-Mailing-List: |
|
TO: |
|
Return-Path: |
<TechNet-request> |
Resent-Message-ID: |
<"Bs5k61.0.hpQ.0ucNp"@ipc> |
Subject: |
|
From: |
|
From [log in to unmask] Tue Apr 29 08: |
42:18 1997 |
X-Loop: |
|
Message-Id: |
|
Parts/Attachments: |
|
|
Using "dash" lines to indicate that a component is "loaded" from the
opposite side of the silk-screen is acceptable within most manufacturing
design guidelines, when only one side of the pwb is screened.
If both sides are screened, a question of why a "dashed" line on the
"other side" of the load comes to mind.
good luck,
thom
______________________________ Reply Separator _________________________________
Subject: Silkscreen practices
Author: [log in to unmask] at Internet
Date: 4/22/97 9:16 PM
Received: by ccmail
Received: from uunet by xl.com (UUPC/extended 1.11) with UUCP;
Tue, 22 Apr 1997 21:15:59 EDT
Received: from simon.ipc.org by relay6.UU.NET with SMTP
(peer crosschecked as: www.ipc.org [209.42.29.3])
id QQcmlg22203; Tue, 22 Apr 1997 21:03:42 -0400 (EDT)
Received: from ipc.org by simon.ipc.org via SMTP (940816.SGI.8.6.9/940406.SGI)
id TAA09504; Tue, 22 Apr 1997 19:50:31 -0700
Resent-Date: Tue, 22 Apr 1997 19:50:31 -0700
Received: by ipc.org (Smail3.1.28.1 #2)
id m0wJqGp-000BjpC; Tue, 22 Apr 97 19:50 CDT
Resent-Sender: [log in to unmask]
Old-Return-Path: <[log in to unmask]>
Mime-Version: 1.0
Date: Mon, 21 Apr 1997 14:42:05 -0500
Message-Id: <[log in to unmask]>
From: [log in to unmask] (SDalton)
X-ccAdmin: NOBODY@uunet
Subject: Silkscreen practices
To: [log in to unmask]
Content-Type: text/plain; charset=US-ASCII
Content-Transfer-Encoding: 7bit
Content-Description: cc:Mail note part
Resent-Message-ID: <"F_6K32.0.PLJ.SpLNp"@ipc>
Resent-From: [log in to unmask]
X-ccAdmin: NOBODY@uunet
X-Mailing-List: <[log in to unmask]> archive/latest/12151
X-Loop: [log in to unmask]
Precedence: list
Resent-Sender: [log in to unmask]
Has anyone heard of using a dashing connector silkscreen outline to
designate that a connector be placed on the solder side of the board
vs. the component side? I realize that dashed lines on drawing
designate this, but I have never seen it on the actual PCB.
Shaun Dalton
Harris
[log in to unmask]
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To subscribe/unsubscribe send a message <to: [log in to unmask]> *
* with <subject: subscribe/unsubscribe> and no text in the body. *
***************************************************************************
* If you are having a problem with the IPC TechNet forum please contact *
* Dmitriy Sklyar at 847-509-9700 ext. 311 or email at [log in to unmask] *
***************************************************************************
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To subscribe/unsubscribe send a message <to: [log in to unmask]> *
* with <subject: subscribe/unsubscribe> and no text in the body. *
***************************************************************************
* If you are having a problem with the IPC TechNet forum please contact *
* Dmitriy Sklyar at 847-509-9700 ext. 311 or email at [log in to unmask] *
***************************************************************************
|
|
|