Hi Jeffery,
You might check out these guys (
https://linkprotect.cudasvc.com/url?a=https%3a%2f%2fwww.micross.com%2fcorfin-industries-is-now-micross%2f&c=E,1,UmoToKlwaSSzggkBaETs929Yrqlokc8PjkoRqzI7qcnhEp4o6WxmgKliY8aj9j_DlGXOzacVLp3ERnio8Oda0RsQMnvxEuPpW8tjs4Bbpg,,&typo=1 ) I dealt with
them years ago when they were Corfin Industries and they were some of the
best, looks now that there's a lot more capability there than when I dealt
with them.
Steve
On Wed, Feb 2, 2022 at 12:07 PM Jenkins, Jeffrey (US) <
[log in to unmask]> wrote:
> Hi Technet,
>
> I'm hoping that someone on here may be able to provide me some guidance as
> to a vendor that can do solder ball install for me. This isn't a reball
> effort, but most likely takes similar expertise.
> My current vendors are not able to handle the quantity and size of the
> spheres as they're more setup for indiviaual ICs.
>
> In short, I have 2 custom designed RF filters on Rogers based material
> - about .200"x .350" (about the size of your pinky finger nail)
> - Panelized array (about 18 up, still finalizing)
> - balls for one filter are 11mils in diameter, the other 13mils. All
> tin-lead.
> - 17 balls per filter.
> - 17000 filters in total need balls installed
> - Also depanelize and put in trays that we'll provide.
>
> This is more of packaging effort I feel. I have reached out to a few
> places with
> https://urldefense.com/v3/__https://isipkg.com__;!!Ooxr18I!RAwausYDiet2tXYHGV76FCF0f4OEJoV0ixMnt8tKhhWPDt7QAr9dCI1lYsAMZM3U6EhJ$
> being one of them, but I've not heard anything back so I'm looking for
> other leads.
>
> Any help is greatly appreciated.
>
> Best,
>
> -Jeffrey
>
>
>
> Jeffrey Jenkins, CID+/CIT
> Principal Engineering Designer Lead
> [log in to unmask]
>
> This message has been marked as Public on 2/2/2022 11:07 AM.
> ________________________________
>
> This electronic message contains information from Cubic or subsidiary
> companies, which may be company sensitive, proprietary, privileged or
> otherwise protected from disclosure. The information is intended to be used
> solely by the recipient(s) named above. If you are not an intended
> recipient, be aware that any review, disclosure, copying, distribution or
> use of this transmission or its contents is prohibited. If you have
> received this transmission in error, please notify the sender immediately.
> With the exception of messages sent by authorized Cubic contracts or
> purchasing personnel, nothing in this message may be interpreted as a
> digital or electronic signature that can be used to: (a) authenticate
> either the submission or the acceptance of a proposal or offer to contract,
> or (b) modify an existing contract. EXPORT COMPLIANCE: Information of a
> technical nature contained in this email or any of its attachments may be
> controlled by the U.S. International Traffic in Arms Regulations or the
> U.S. Export Administration Regulations and may therefore not be exported,
> released, or disclosed to non-U.S. persons worldwide unless in compliance
> with applicable export controls. Violations of U.S. export control laws are
> punishable by fine and/or imprisonment.
>
> ________________________________
>
--
Steve Gregory
Kimco Design and Manufacturing
Process Engineer
(208) 322-0500 Ext. -3133
Cell Phone: (918) 706-2779
--
This email and any attachments are only
for use by the intended
recipient(s) and may contain legally privileged,
confidential, proprietary
or otherwise private information. Any
unauthorized use, reproduction,
dissemination, distribution or other
disclosure of the contents of this
e-mail or its attachments is strictly
prohibited. If you have received
this email in error, please notify the
sender immediately and delete the
original.
|
