DESIGNERCOUNCIL Archives

March 2016

DesignerCouncil@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
Ben Jordan <[log in to unmask]>
Reply To:
(Designers Council Forum)
Date:
Wed, 16 Mar 2016 13:22:59 -0700
Content-Type:
text/plain
Parts/Attachments:
text/plain (133 lines)
On Q2, you're looking at total trace width and fusing current. But the
thing about thermals is that because the spoke is next to a huge copper
area (presumption), the current can be much higher in the spoke than a long
trace of the same width without any risk of burning.

Doug Brooks has done some thorough investigations into this. He's got some
incredible resources: http://ultracad.com/article_temperature.htm

On Wed, Mar 16, 2016 at 12:35 PM, Guy Ramsey <[log in to unmask]> wrote:

> The standard requires the solder be wetted to the lead and the PTH.
> On Mar 16, 2016 3:30 PM, "Jack Olson" <[log in to unmask]> wrote:
>
> > I posted this to IPC TechNet, but I think many people are busy at APEX
> this
> > week:
> >
> > -=-=-=-
> >
> > Maybe I should know better than to ask two questions in the same email,
> but
> > they're related...
> > I got into a discussion about the hole fill requirement for some large
> > through-hole power devices and connectors. The supplier is worried about
> > using a "percentage" hole fill measurement, because he says that even if
> > the hole is 75% full (or whatever percentage we want to use) the hole
> wall
> > will not be WETTED 75%. He maintains that the cold solder can extend up
> > farther than the actual portion that makes a good joint. So he is looking
> > at the TOP PAD WETTING for verification of a good solder joint, even
> though
> > we don't require it.
> >
> > Q1) It seems like an inspection procedure looking for WETTING instead of
> > HOLE FILL is not what is intended in IPC, but does he have a point? The
> > hole fill problem is with Selective Soldering, not Reflow
> >
> > Q2) Wanting to provide bare board designs using good DFM practices, I
> would
> > be willing to reduce my thermal spoke widths so the solder will flow
> > better, but I can't find a calculation that would tell me what I need for
> > something like 10A. There is nothing about this in the IPC-2152 Current
> > Carrying standard. Is there a rough guideline I can use for current
> through
> > planes using thermal relief??
> >
> > thanks,
> > Jack
> >
> >
> > ______________________________________________________________________
> > This email has been scanned by the Symantec Email Security.cloud service.
> > For more information please contact helpdesk at x2960 or
> [log in to unmask]
> > ______________________________________________________________________
> >
> >
> >
> ---------------------------------------------------------------------------------
> > DesignerCouncil Mail List provided as a free service by IPC using
> LISTSERV
> > 16.0.
> > To unsubscribe, send a message to [log in to unmask] with following text
> in
> > the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
> > To temporarily stop/(restart) delivery of DesignerCouncil send: SET
> > DesignerCouncil NOMAIL/(MAIL)
> > For additional information, or contact Keach Sasamori at [log in to unmask]
> > or 847-615-7100 ext.2815
> >
> >
> ---------------------------------------------------------------------------------
> >
>
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud service.
> For more information please contact helpdesk at x2960 or [log in to unmask]
> ______________________________________________________________________
>
>
> ---------------------------------------------------------------------------------
> DesignerCouncil Mail List provided as a free service by IPC using LISTSERV
> 16.0.
> To unsubscribe, send a message to [log in to unmask] with following text in
> the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
> To temporarily stop/(restart) delivery of DesignerCouncil send: SET
> DesignerCouncil NOMAIL/(MAIL)
> For additional information, or contact Keach Sasamori at [log in to unmask]
> or 847-615-7100 ext.2815
>
> ---------------------------------------------------------------------------------
>




______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________
-- 
*Ben Jordan*
Director, Community Tools and Content

4225 Executive Sqr., Suite 700, La Jolla CA 92037 USA
Tel: +1-858-864-1539 Mob: +1-760-212-6720

*octopart.com <http://octopart.com> | circuitmaker.com
<http://circuitmaker.com> | altium.com <http://altium.com>*
------------------------------
This email message, including any attached files, is confidential and
intended solely for the use of the individual or entity to whom it has been
addressed. Altium prohibits the right to publish, copy, distribute or
disclose any information contained in this email, or its attachments, by
any party other than the intended recipient. If you have received this
email in error please notify the sender and delete it from your system.
------------------------------


______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________

---------------------------------------------------------------------------------
DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 16.0.
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
To temporarily stop/(restart) delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL/(MAIL)
For additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
---------------------------------------------------------------------------------

ATOM RSS1 RSS2