Mark, et al, Sorry for a blunder on my part. IPC-2222 uses the term 'Level A', etc, rather than Class. I was just back over in the inspection area and noticed my mistake. Classes seem to be connected to tolerance on mechanical dimensions. Louis
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Woolley, Mark D. (Mark)
Sent: Thursday, October 30, 2008 11:13 AM
To: [log in to unmask]
Subject: Re: [TN] IPC 2222 classes
Louis,
I haven't looked at IPC-2222 but in IPC-600 and IPC-610 the definition
of classes is located in the beginning of the spec, in the introduction.
Briefly:
Class 1: General consumer electronics. Cosmetic imperfections
are allowable, and functionality after assembly is most important item
on list.
Class2: Communications equipment, business equipment. High performance
and reliability are desired, but no one dies if the equipment quits.
Class 3: High Reliability, life support, flight systems,
reliability is critical.
Hope this helps.
mark
Mark Woolley
PTRL Laboratory
Avaya, 1300 West 120th Ave, Area 33, Westminster, CO, 80234
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Louis Hart
Sent: Thursday, October 30, 2008 7:50 AM
To: [log in to unmask]
Subject: [TN] IPC 2222 classes
TechNetters, looking at IPC-2222, I see references to Class A, Class B,
and Class C. I can't find a definition of the 3 classes in the document.
Would someone comment on how these classes are assigned or determined?
The question arose in the context of looking at a drawing with no
dimensional tolerances. I'm asking for tolerances from the customer, but
want to do my own homework on the issue. Thanks. Louis
Louis Hart
Compunetics
Monroeville, PA
USA
[log in to unmask]<mailto:[log in to unmask]>
412-858-1272
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|