Gary, here a slide presentation from our counterfeit training/workshop
by that link I sent you, Jon
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Gary Camac
Sent: Tuesday, September 09, 2008 1:25 PM
To: [log in to unmask]
Subject: Re: [TN] What's under the blacktop
John,
Ya, I thought of the sand paper thing. I am thinking of using our PWB
cross-sectioning equipment to polish off the applied surface. The
current layer on these ICs has been laser marked. I have been able to
find a component on one of our technicians test PWAs that I am certain
was a factory part. It is marked with ink. So, I am thinking of trying
to polish my way down to the ink layer. The layer I am trying to hit is
about as thin as my chance of success.
These are brokered components, end-of-life kind of thing, buyer beware,
what you see is all you can get...et. al. We have seen isolated
soldering problems and a some dead ICs.
Thanks for the input,
Gary Camac
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of John Burke
Sent: Tuesday, September 09, 2008 12:30 PM
To: [log in to unmask]
Subject: Re: [TN] What's under the blacktop
It depends,
If the device was marked with ink it was almost certainly removed
abrasively
before black top and re-marking.
If the device was laser marked there is some hope as normally these are
double black topped to fill in the impression left by the laser before
re-marking. In this case a VERY fine grade of abrasive paper should
reveal
the original marking.
Did you ask the vendor?? There are many reasons for re-marking most of
them
not bad (and some very bad)
John Burke
(408) 515 4992
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Gary Camac
Sent: Tuesday, September 09, 2008 9:33 AM
To: [log in to unmask]
Subject: [TN] What's under the blacktop
Good morning,
We have some ICs that appear to have been blacktopped. (Steve G. -
thanks for the excellent link in July).
Now the question is why - what is covered up? Our concern is that
commercial grade is being identified as industrial.
Is there a method for looking under the blacktop to determine what was
there before the cover-up?
Thanks,
Gary
Gary Camac
Senior Manufacturing Engineer
DICKEY-john Corp.
5200 Dickey John Road
Auburn, IL 62616-0010
Telephone 217-438-2288
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask]
or
847-615-7100 ext.2815
-----------------------------------------------------
__________ NOD32 3429 (20080909) Information __________
This message was checked by NOD32 antivirus system.
http://www.eset.com
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
This communication is intended only for use by the addressee(s) named herein and may contain business confidential and/or legally privileged information. If you are not the intended recipient of this e-mail, you are hereby notified that any dissemination, distribution, disclosure or copying of this e-mail and its contents is strictly prohibited. If you have received this e-mail in error, kindly notify the sender by replying to this message. In addition, please permanently delete the message and any attachments without copying or disclosing the contents. Thank you for your cooperation.
THIS DOCUMENT AND/OR SHIPMENT MAY CONTAIN COMMODITY ITEMS, SOFTWARE OR TECHNICAL DATA THAT IS CONTROLLED BY U.S. EXPORT LAW, AND MAY NOT BE EXPORTED OUTSIDE THE UNITED STATES OR TO NON U.S. PERSONS WITHOUT THE APPROPRIATE EXPORT LICENSE FROM EITHER THE U.S. DEPARTMENT OF STATE OR DEPARTMENT OF COMMERCE.
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|