Subject: | |
From: | |
Reply To: | |
Date: | Tue, 6 Mar 2007 16:58:11 -0500 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Words of wisdom born from logic.
Jeffrey Bush
Director, Quality Assurance and Technical Support
VERMONT CIRCUITS INCORPORATED
76 Technology Drive - POB 1890
Brattleboro, Vermont 05302
Voice - 802.257.4571 ext 37
Fax - 802.257.0011
<http://www.vtcircuits.com/>
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Wayne Thayer
Sent: Tuesday, March 06, 2007 3:52 PM
To: [log in to unmask]
Subject: Re: [TN] immersion silver and exposed copper in small vias
And what's wrong with exposed copper? You certainly aren't going to try
and solder down there, are you? Copper does not corrode quickly, and if
its going to be in a corrosive environment, you're going to have to
conformal coat anyway!
The silver is put on boards only to extend the solderability lifetime
of the bare copper, not as a protectant to prevent opens due to
corrosion.
This is not a reliability issue at all.
Wayne Thayer
>>> [log in to unmask] 3/6/2007 12:10:08 pm >>>
Hi Fran
The amount of mask intruding into the hole will depend on the
application method. Our curtain coat operation can cause the mask
(circa
1-2 microns) to penetrate about 1/3rd into the hole from both sides
but
it has not affected the silver taking on the remaining surface. Is the
mask too thick at the hole entrance to prevent the plating solution
getting good access?
You may also need to confirm by micro section what your customer
thinks
he is seeing. Is the mask covering all the hole surface? Hope this
helps.
Regards
Alistair
Alistair F Murray MICT
Technical Manager
Artetch Circuits Limited
England UK
Direct Dial: 01903-712931
www.artetch.co.uk
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Fran Juliot
Sent: 06 March 2007 15:58
To: [log in to unmask]
Subject: [TN] immersion silver and exposed copper in small vias
Our customer is questioning what they feel is exposed copper in 8 mil
vias holes on silver boards. We feel there is mask residue in the
holes
which does not allow silver to take. These are holes that are allowed
to be plugged. Has anyone else ran into this issue with thier
customers
and do you have the same look or are your small vias covered with
silver
all the way through the via?
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt
or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
|
|