It wasn't a typo! It was measured with a handheld charge meter in a short
distance from a duster in a low humidity (30 % R.H.) environment. Increasing
the humidity to 50 % will degrease the charge to 35 kV.

The problem is that our customer has used a duster to wipe of dust from the
equipment and the LCD-drivers goes to Latch-Up-state with undesired
consequences.

Now there has been discussion about the sustainability of the equipment
against such operation. There are solutions to improve the sustainability
but the question is how to test it.

I have a strong feeling that instead of making any changes to equipment we
should give instructions to user how to clean our products (with damp towel,
not with duster).

B.R.
Jarmo

> -----Original Message-----
> From: Phil Bavaro [SMTP:[log in to unmask]]
> Sent: 22. toukokuuta 2000 18:36
> To:   [log in to unmask]
> Subject:      Re: [TN] Brush dust off on equipment with duster
>
> That has to be a typo.....70 kV is way too high to be generated with a
> simple duster.
>
> Please tell us how this 70kV was measured and who makes it if in fact it
> does generate that type of charge.
>
>
> No matter what the actual number is, I would not want it around our ESDS
> components.  As far as equipment which is sealed up is concerned, it
> really
> depends on what it is.
>
>
> Our policy is not to allow the dusters in our factories as we use a
> topical
> cleaner and a lint free wipe to remove dust.
>
>
> Regards,
>
> Phil
>
> At 09:04 AM 5/22/00 +0300, Kiiski Jarmo wrote:
> >Hi,
> >
> >Is there any ESD specialists listening!
> >
> >Should the electronic equipment sustain the use of duster?
> >
> >Is there a method to test the durability of equipment against duster?
> >
> >According to our experience the charge of a duster can be over 70 kV.
> >
> >B.R.
> >Jarmo Kiiski
> >
> >##############################################################
> >TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
> >##############################################################
> >To subscribe/unsubscribe, send a message to [log in to unmask] with
> following
> >text in
> >the body:
> >To subscribe:   SUBSCRIBE TECHNET <your full name>
> >To unsubscribe:   SIGNOFF TECHNET
> >##############################################################
> >Please visit IPC web site (http://www.ipc.org/html/forum.htm) for
> additional
> >information.
> >If you need assistance - contact Keach Sasamori at [log in to unmask] or
> >847-509-9700 ext.5315
> >##############################################################
> >
>
> ##############################################################
> TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
> ##############################################################
> To subscribe/unsubscribe, send a message to [log in to unmask] with
> following text in
> the body:
> To subscribe:   SUBSCRIBE TECHNET <your full name>
> To unsubscribe:   SIGNOFF TECHNET
> ##############################################################
> Please visit IPC web site (http://www.ipc.org/html/forum.htm) for
> additional
> information.
> If you need assistance - contact Keach Sasamori at [log in to unmask] or
> 847-509-9700 ext.5315
> ##############################################################

##############################################################
TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
##############################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in
the body:
To subscribe:   SUBSCRIBE TECHNET <your full name>
To unsubscribe:   SIGNOFF TECHNET
##############################################################
Please visit IPC web site (http://www.ipc.org/html/forum.htm) for additional
information.
If you need assistance - contact Keach Sasamori at [log in to unmask] or
847-509-9700 ext.5315
##############################################################