Hi Jerry,
倒没相应文件或标准支持，本人认为其实从烙铁的恒温机理可以理解，
需检测的就是烙铁设定温度，通常T1=T2,因此测温仪的温度不变化时再读取是最准确，至于3s，烙铁头无法达到预设温度,这是和烙铁的回温慢或所接触的焊接对象吸热快相关的，希望能解析到你的问题。

[cid:[log in to unmask]]

Regards!

From: Jerry Li [mailto:[log in to unmask]]
Sent: 2012年6月7日 14:42
To: Lau, David [NETPWR/EMBCO/CN]
Cc: [log in to unmask]
Subject: RE: 手工焊接烙铁温度点检方法

Hi David
“测温仪的温度不变化时再读取是最准确的”，目前是否有相应文件或标准支持？
如果以测温仪的温度不变化时再读取是最准确的话，就会造成在焊接时间内，如3s，烙铁头往往无法达到预设温度,如何处理？
谢谢。
Jerry

From: TGAsia [mailto:[log in to unmask]] On Behalf Of David Lau
Sent: Wednesday, June 06, 2012 10:56 AM
To: [log in to unmask]<mailto:[log in to unmask]>
Subject: Re: [TGAsia] 手工焊接烙铁温度点检方法

Dear Jerry,
测温仪的温度不变化时再读取是最准确的。

Regards!

From: TGAsia [mailto:[log in to unmask]] On Behalf Of Wellington Li
Sent: 2012年6月6日 10:23
To: [log in to unmask]<mailto:[log in to unmask]>
Subject: [TGAsia] 答复: 手工焊接烙铁温度点检方法

Dear Jerry
     类似问题，一般是客户访厂时会提出的。
     点检哪个温度都有正确性，关键是要理解两个时间点的不同含义，以及过程控制的关注点。

发件人: TGAsia [mailto:[log in to unmask]] 代表 Jerry Li
发送时间: 2012年6月6日 8:59
收件人: [log in to unmask]<mailto:[log in to unmask]>
主题: [TGAsia] 手工焊接烙铁温度点检方法

请教：手工焊接中通常以烙铁头的实际温度为焊接温度，那么如何点检烙铁头温度？温度如何读取，是3S读取还是测温仪的温度不变化时再读取？
谢谢

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]<mailto:[log in to unmask]>
______________________________________________________________________

________________________________________________________________________

Visit the BSI website at www.bsigroup.com<http://www.bsigroup.com>

This email may contain confidential information and/or copyright
material. This email is intended for the use of the addressee only.
Any unauthorised use may be unlawful. If you receive this email
by mistake, please advise the sender immediately by using the
reply facility in your email software.

The British Standards Institution is incorporated by Royal Charter.

This email has been scanned for all known viruses.

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]<mailto:[log in to unmask]>
______________________________________________________________________

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]<mailto:[log in to unmask]>
______________________________________________________________________

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please visit http://www.symanteccloud.com
______________________________________________________________________

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________