Glen,
My interpretation has been 0.5% per inch, especially for boards with
(large) BGA's. You can have an overall warp of 0.5% that is considerably
more in local areas, so if I have concernes about warpage, I check the
critical areas as well as the overall board. If your boards are properly
made, they shouldn't warp any more as a result of assembly processing. The
acceptable degreee of warping, within recognised limits, depends on how
flat YOU need the board to be. If you receive boards from your fab house
that are regularly warped close to the IPC acceptable limit, and this is
not good enough for your vacuum processes, you will have to impose tighter
tolerances yourself. If your fab house cannot meet your requirements -
well, time to find a new fab house that can.
Tough ol' world, ain't it?
Peter
Glenn Pelkey <[log in to unmask]> 29/10/2002 01:13 AM
Sent by: TechNet <[log in to unmask]>
Please respond to "TechNet E-Mail Forum."; Please respond to glenn.r.pelkey
To: [log in to unmask]
cc: (bcc: DUNCAN Peter/Asst Prin Engr/ST Aero/ST Group)
Subject: Re: [TN] WARPAGE
We apply IPC-6015 to much of our product, which requires 0.5%. After SMT,
there are a number of fixtures that require the board to be flat for vacuum
hold down or epoxy dispense processes.
Now tell me if I'm interpreting this wrong. I apply the 0.5% limit at
incoming, and apply the 0.75% limit after SMT. Sound correct?
Glenn
-----Original Message-----
From: Franklin D Asbell [mailto:[log in to unmask]]
Sent: Monday, October 28, 2002 8:31 AM
To: [log in to unmask]
Subject: Re: [TN] WARPAGE
Would that criteria also apply to "populated" boards? I believe he
was seeking data for populated boards...curious...would it matter
after assembly if they were warped or not???
Franklin
----- Original Message -----
From: Eric Castonguay
To: [log in to unmask]
Sent: Monday, October 28, 2002 10:14 AM
Subject: Re: [TN] WARPAGE
Pankaj,
check in IPC-6012 par. 3.4.4 Bow & Twist. The printed board shall
have a maximum bow & twist of 0.75% for boards that use SM
components and 1.5% for all other boards. Also, see test method
2.4.22 described in the "IPC-TM-650 test methods manual" on how to
measure it.
Eric Castonguay, Eng.
Manufacturing Engineering
www.Hyperchip.com
Montreal, Canada
T. 514 906 2409
F. 514 906 2501
-----Original Message-----
From: Karnwal, Pankaj [mailto:[log in to unmask]]
Sent: Monday, October 28, 2002 02:02
To: [log in to unmask]
Subject: [TN] WARPAGE
> Hi TechNet
>
> Can any body give me the acceptable range of PCB {Populated } For
> Warpage, { Both Throughole And SMD And MIX components} .And how
we can
> measure it. Also tell that what IPC states about this.
>
>
> With regards
> Pankaj Karnwal
> Quality Assurance Ext. 211
> BESL A-4,Sec-5 NOIDA , 201301, INDIA
> e mail : <mailto:[log in to unmask]>
> Barco, innovators in image processing
>
>
>
- - - - - - - - DISCLAIMER - - - - - - - -
Unless indicated otherwise, the information contained in this
message is
privileged and confidential, and is intended only for the use of the
addressee(s) named above and others who have been specifically
authorized to
receive it. If you are not the intended recipient, you are hereby
notified
that any dissemination, distribution or copying of this message
and/or
attachments is strictly prohibited. The company accepts no liability
for any
damage caused by any virus transmitted by this email. Furthermore,
the
company does not warrant a proper and complete transmission of this
information, nor does it accept liability for any delays. If you
have
received this message in error, please contact the sender and delete
the
message. Thank you.
---------------------------------------------------
Technet Mail List provided as a free service by IPC using LISTSERV
1.8e
To unsubscribe, send a message to [log in to unmask] with following
text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/html/forum.htm for
additional
information, or contact Keach Sasamori at [log in to unmask] or
847-509-9700 ext.5315
-----------------------------------------------------
--------------------------------------------------- Technet Mail
List provided as a free service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text
in the BODY (NOT the subject field): SIGNOFF Technet To temporarily
halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE
mailing per day of all the posts: send e-mail to [log in to unmask]:
SET Technet Digest Search the archives of previous posts at:
http://listserv.ipc.org/archives Please visit IPC web site
http://www.ipc.org/html/forum.htm for additional information, or
contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
-----------------------------------------------------
--------------------------------------------------- Technet Mail List
provided as a free service by IPC using LISTSERV 1.8e To unsubscribe,
send a message to [log in to unmask] with following text in the BODY
(NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/html/forum.htm for
additional information, or contact Keach Sasamori at [log in to unmask]
or 847-509-9700 ext.5315
-----------------------------------------------------
--------------------------------------------------- Technet Mail List
provided as a free service by IPC using LISTSERV 1.8e To unsubscribe, send
a message to [log in to unmask] with following text in the BODY (NOT the
subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery
of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To
receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest Search the archives of previous posts
at: http://listserv.ipc.org/archives Please visit IPC web site
http://www.ipc.org/html/forum.htm for additional information, or contact
Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
-----------------------------------------------------
[This e-mail is confidential and may also be privileged. If you are not the
intended recipient, please delete it and notify us immediately; you should
not copy or use it for any purpose, nor disclose its contents to any other
person. Thank you.]
---------------------------------------------------
Technet Mail List provided as a free service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/html/forum.htm for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
-----------------------------------------------------
|