TECHNET Archives

May 2007

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Condense Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Sender:
X-To:
TechNet E-Mail Forum <[log in to unmask]>, "Wenger, George M." <[log in to unmask]>
Date:
Thu, 24 May 2007 12:36:37 -0500
Reply-To:
TechNet E-Mail Forum <[log in to unmask]>, Steve Gregory <[log in to unmask]>
Subject:
From:
Steve Gregory <[log in to unmask]>
Content-Transfer-Encoding:
quoted-printable
In-Reply-To:
Content-Type:
text/plain; charset="us-ascii"
MIME-Version:
1.0
Parts/Attachments:
text/plain (189 lines)
Hi George!

Good guess, I was thinking the same thing...

See the exchange I pasted below...

Steve Gregory

****************************************************

Hi Steve,

The lead frame consists mostly of Alloy 42 which consists, primarily, of
nickel and iron.

Typical Alloy 42 composition:

NICKEL(NI) - 39/41% 
CHROMIUM(CR) - 0.05 
MANGANESE(MN) - 0.60 
SILICON(SI) - 0.02 
CARBON(C) - 0.05 
COBALT(CO) - 0.05 
PHOSPHORUS(P) - 0.02 
SULFUR(S) - 0.02 
IRON(FE) - REMAINDER

Hope this answers your questions.

Thank you very much, 
-Vyjayanthi 


------------------------------------------------------------------------
--------

From: Steve Gregory [mailto:[log in to unmask]] 
Sent: Thursday, May 24, 2007 11:03 AM
To: vprasad
Subject: Leadframe material for MT46V16M16TG-6T DDR SDRAM

Good Day!

Thanks for returning my call. I would like to find out what the
leadframe material is for the MT46V16M16TG-6T DDR SDRAM.

I had looked in the datasheet, but could not find it.

Kind regards,

Steve Gregory
Production Engineer
OAI Electronics
6960 East 12th Street
Tulsa, Oklahoma 74112

(918) 836-9077 ext 507
(918) 836-0184 FAX


-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Wenger, George M.
Sent: Thursday, May 24, 2007 9:27 AM
To: [log in to unmask]
Subject: Re: [TN] Silver Embrittlement?

My guess is that the TSOP packages do have Alloy 42 lead  Steve,

My guess is that the TSOP packages do have Alloy 42 leads and that you
may be seeing a failure that has gotten the name "Double Reflow"  I hate
that name almost as much as I hate the name "Black pad".  What do the
solder fillets look like on your TSOP packages?  If they look good but
your testing is indicating an intermittent and you can pass test by
pushing down on a TSOP lead I think you most likely have a brittle
interface solder joint fracture.  It will look like a perfect surface
mount solder joint with nice feathered solder fillets like it is wet
well to the PCB pad, and it probably was when it was formed.  However,
then the temperature is elevated and there is any mechanical stress the
solder joint can facture at the IMC bulk solder interface.  You won't be
able to see the fracture unless you view it at a low angle under high
magnification.  The "Double Reflow" name was coined by IBM Austin back
in 1979 presentation at NEPCON.  They called it "Double Reflow" because
their surface mount solder joints look great after surface mount reflow
soldering but failed (fractured) after the boards were wave soldered
(i.e., failed at the second reflow).  I've attached their NEPCON paper
as well as one we did describing a solder joint fracture we had using
QFPs with Alloy 42 leads.  We also saw similar failures on another
product on corner leads after the initial surface mount reflow.  Those
failures occurred during the first reflow and had nothing to do with
double reflow.  The solder joint fractures occurred on corner leads
during the surface mount reflow cooling process.

Regards,
George
George M. Wenger
Senior Principle FMA / Reliability Engineer Wireless network Solutions
Andrew Corporation, 40 Technology Drive, Warren, NJ 07059 (908) 546-4531
[log in to unmask] 


-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Steve Gregory
Sent: Thursday, May 24, 2007 8:45 AM
To: [log in to unmask]
Subject: [TN] Silver Embrittlement?

Mornin' all!
 
I know this subject has been talked about before, but my memory is
getting rusty. I was wondering if it was possible to get solder joint
embrittlement on a board that has immersion silver finish and components
that have a flash gold finish? As you might have guessed, it's those
pesky Samtec SMT connectors...
 
We're experiencing another issue on that board as well. We're seeing
solder joint problems with some TSOP-66 DDR SDRAM that are on the
topside of the board. They're arranged close around two XILINX 1152-ball
BGA's that get very hot when the assembly is under power. Both BGA's
have large finned heatsinks mounted to the top of them. The BGA's get so
hot that if you power the board up without the heatsinks, and touch one
of the BGA's, you will burn your finger. There have been some cases that
during testing the board will fail and the failure points to one of the
SDRAM TSOP's. If you take something like the end of a wooden Q-Tip and
press on a suspect lead, the board passes test. The solder joint looks
fine upon initial inspection, but there's obviously an open connection.
I remember at one time TSOP leadframe material used to be made of
Alloy-42, is that still the case? These are parts from Micron
(MT46V16M16TG-6T), and I haven't yet found what the leadframes are made
of. I'm wondering if the stiffness of the leads may be contributing to
the solder joint failures that we're seeing. My theory is that because
the BGA's run so hot, they heat the PCB and cause board to expand in the
area around them (where the SDRAM are mounted).
If the leads on the SDRAM are stiff and non-compliant, the solder joints
might fracture.
 
Crazy theory I know, but I'm trying to figure what's going on with these
boards...
 
Steve Gregory 
	

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------

------------------------------------------------------------------------
------------------------
This message is for the designated recipient only and may contain
privileged, proprietary, or otherwise private information.  
If you have received it in error, please notify the sender immediately
and delete the original.  Any unauthorized use of this email is
prohibited.
------------------------------------------------------------------------
------------------------
[mf2]


---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------

ATOM RSS1 RSS2