TECHNET Archives

May 2008

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Condense Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Sender:
X-To:
TechNet E-Mail Forum <[log in to unmask]>
Date:
Mon, 19 May 2008 09:00:02 -0400
MIME-version:
1.0
Reply-To:
TechNet E-Mail Forum <[log in to unmask]>, "Gumpert, Ben" <[log in to unmask]>
Content-type:
text/plain; charset=US-ASCII
Subject:
From:
"Gumpert, Ben" <[log in to unmask]>
In-Reply-To:
Content-transfer-encoding:
7BIT
Parts/Attachments:
text/plain (56 lines)
Ashok,

Looks like you answered your own question.
20 mil pad design - (2.5 mil etch x 2 sides) = 15 mil pad actual > 10
mils 

Ben

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Ashok Dhawan
Sent: Thursday, May 15, 2008 9:05 PM
To: [log in to unmask]
Subject: [TN] Solder Pad width

I am looking for measured pad width for 20 mil land pattern for SMT.
(QFP or TSOP) 

What is Pad width actal versus top copper layer?  Copper outer layer is
1 oz or 2 oz or 3 ozs. 

Reason for this question: Stencil is 6mils thick with min aperture
opening of 9 mils. For gasketing, the pad need to o=be over 10 mils. 

2 Ozs copper has etch factor 2.5 mils over etch each side. Can final pad
width of over 10 mils be made.

Any inputs on this will be appreciated.

Regards


Ashok

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------

ATOM RSS1 RSS2