Hi Bev! If you are going to conduct the rework by manual soldering then
filling the hole shouldn't be a big deal in comparison to some type of
automated pin-in-paste rework. What I am curious about is how do you get
an "oval" hole? Aren't Canadian drill bits round too? : - )
Dave Hillman
Rockwell Collins
[log in to unmask]
Bev Christian <[log in to unmask]>
Sent by: TechNet <[log in to unmask]>
07/16/2007 10:43 AM
Please respond to
TechNet E-Mail Forum <[log in to unmask]>; Please respond to
Bev Christian <[log in to unmask]>
To
[log in to unmask]
cc
Subject
[TN] Question about rework of paste in hole solder joints
Technetters,
Good morning! We generally do not use PTH parts. As a result, we do
not do wave soldering, but use paste-in-hole or pin-in-paste, chose your
moniker. Because we buy the part in question from two different
suppliers, who make the parts with different dimensions, we have had to
use fairly large, oval holes instead of a more conventional round hole.
And the part leads do not stick out the bottom of the hole either. With
overprinting we have been able to get what is deemed adequate solder
joint strength (and reliability (Yes, I know the difference, Werner.)),
even though the hole fill is not stellar. Wetting angles are good and
proper intermetallics are formed.
Now let's say we do a rework - removing the component, dressing the
hole, inserting a new part and resoldering using hand soldering with
cored wire. The internal debate is whether we should demand hole fill
to meet normal IPC standards or whether we allow the same amount of hole
fill that is allowed for the original paste-in-hole. Opinions and/or
experiences (if you are willing to share the latter :) ) appreciated.
Thanks in advance.
Bev
RIM
---------------------------------------------------------------------
This transmission (including any attachments) may contain confidential
information, privileged material (including material protected by the
solicitor-client or other applicable privileges), or constitute non-public
information. Any use of this information by anyone other than the intended
recipient is prohibited. If you have received this transmission in error,
please immediately reply to the sender and delete this information from
your system. Use, dissemination, distribution, or reproduction of this
transmission by unintended recipients is not authorized and may be
unlawful.
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|