Hello Robert,
I trust all is well with you in the great Pacific Northwest. It has been a
while since we've crossed paths.
Thanks for taking time to pose your questions. I'd like to share my thoughts
with you on the subject.
First, I personally don't think there is any such thing as a panacea. Nor
must the Occam process be a panacea to be considered a success, it must simply
fill a particular need successfully.
That aside, over time there have always come along some new technologies
that had some advantage in some areas over some incumbent technology or process
solution. But in the present situation, solder is not going to go away
immediately because of Occam. There is simply too much invested in equipment and
people will want to take advantage both of what they have and what they know.
As one bit of supporting evidence, I would note that you can still buy DIPs
even though they are clearly cannot match the size, performance or manufactured
cost benefits of SMT parts.
As for Dr. Ron Lasky's "less than all embracing" attitude, he is selling
solder technology for a living and is not likely to be supportive of any
assembly method or process that proposes to obviates solder's use. Dr. Ron's "meet
the enemy at the gate and attack the threat" approach is thus easy to
understand (though his problem statements are a bit off track in my humble opinion).
Sierra Proto is not as easy to explain since they have been talking about
researching the embedment of resistors and using plating for interconnections.
No worries, in either case, technologies evolve at their own pace and there
are those who choose to risk and drive evolution and those who choose to play
safe and follow. It is normal. Then again, if some folks in this industry
did not risk developing soldering equipment many years ago, we would still be
twisting wires together, so "hats off" to those who chose to drive that early
change from which we have all so greatly benefited. Another good thing, at
least in this industry, there is room for everyone at the table even those who
question the need to change.
Back to your comments... You might have read last week that Georgia Tech has
just announced its own efforts to eliminate solder but that is just the
latest. There is a growing number of house hold name companies around the globe
that have nascent efforts underway to examine the potential of solderless
assembly of their products especially in high reliability applications. For
example a company in Brazil has built and in building assemblies for evaluation
for a customer greatly concerned about all of the problems of lead-free that
continue to be discussed on a daily basis in this forum.
Of course, the proof will be "in the pudding" as the saying goes. and to
answer the question daisy chain assemblies will be run side by side with
lead-free assemblies. Which ones will fail first? That will be seen and you might
have your own predictions but to be honest with you, I have never seen anyone
shake, mechanically shock or thermal cycle the circuits traces off of a PCB
and industry experience with over square aspect ratio plated copper vias has
been very good.
Ultimately, it is about have some small measure of willingness to embrace a
little change and as the editor of one Japanese technical magazine said to
his readers in an article he wrote about the Occam process late last year:
"When evolution happens, always there is resistance". Fortunately, he was someone
whom it appears is in favor of change and evolution or he would not have
written the article.
I look forward to showing you some of the demonstration assemblies that have
been already built the next time we meet. I'll buy the beer... :-)
Very best,
Joe
In a message dated 2/17/2008 8:05:26 AM Pacific Standard Time,
[log in to unmask] writes:
I have been reading about the OCCAM process and the rebuttal of people like
Dr. Ron Lasky and companies like Seirra Protr Express. Does anyone have an
opinion regarding the process and what are its chances of being the panacea
for eliminating the lead free process?
Robert Hanson
**************Ideas to please picky eaters. Watch video on AOL Living.
(http://living.aol.com/video/how-to-please-your-picky-eater/rachel-campos-duffy/
2050827?NCID=aolcmp00300000002598)
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|