TECHNET Archives

May 2008

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Condense Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Sender:
X-To:
TechNet E-Mail Forum <[log in to unmask]>, Richard Olsen <[log in to unmask]>
Date:
Mon, 5 May 2008 14:09:02 -0500
Reply-To:
TechNet E-Mail Forum <[log in to unmask]>, "Stadem, Richard D." <[log in to unmask]>
Subject:
From:
"Stadem, Richard D." <[log in to unmask]>
Content-Transfer-Encoding:
quoted-printable
In-Reply-To:
Content-Type:
text/plain; charset="us-ascii"
MIME-Version:
1.0
Parts/Attachments:
text/plain (78 lines)
We used to have an assembly with mirrored BGAs. Whenever we needed one
reworked I called the design engineer responsible for this fiasco and
told him to get his sorry butt down to the Airvac rework machine. It
wasn't long before it was completely redesigned.

Here is what you can do.
Use Loctite 3609 to cornerbond the BGA on the opposite side. Cure at 150
for about 10 minutes, no more.
Mask off the adjacent components around the BGA you wish to rework with
a high-temp, ESD-safe, non-polyimid tape such as Tapes II T-32 (this is
actually a 3M product). http://www.tapes2.com/electronics.htm
Flux the BGA you are about to rework, and flux the mirror-image BGA on
the opposite side of the assembly as well. That way if it goes into
reflow it will have the advantage of a flux application.
Allow to cool after removing the BGA. Perform the site prep, replace
with the new BGA and reflow that in place. X-ray at an angle so you can
verify both BGAs are good. If X-ray looks good, then remove the masking
tape, run the board through the wash process, and finally chip off the
cornerbonds using a small exacto knife. Do not cut into the PWB.
If the customer allows it, you can leave the cornerbonds on. 
Qualify this process on your product before you jump in and rework a
number of BGAs this way.


-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Richard Olsen
Sent: Monday, May 05, 2008 1:29 PM
To: [log in to unmask]
Subject: [TN] BGAs on opposing sides

Hello,

I have a board before me with multiple BGA's on both sides. In some
places they oppose each other.
Does anyone have any manufacturing ideas for soldering the BGA's?
One I have heard is to mask the first side BGA's and heat through the
mask, BGA, board and finally the pads of the second BGA, finally
removing the mask when done. 

Thanks,
Rich


Richard Olsen
Quality Manager/ Sales & Customer Service RNB Enterprises
17816 North 25th Avenue
Phoenix Arizona
85023-2108

Tel - 602-889-3463
Cel - 602-740-2244
Fax - 602-863-2274
Toll Free (800)-270-7585
www.rnbent.com

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------

ATOM RSS1 RSS2