Subject: | |
From: | |
Reply To: | |
Date: | Mon, 13 Jun 2005 18:44:20 -0700 |
Content-Type: | multipart/mixed |
Parts/Attachments: |
|
|
Hi Kerry,
Please also check the alignment of BGAs prior to reflow. Misaligned BGAs
have cracked at the package side if the package is mask defined and PWB
side is etch defined. Contact area of ball to pad is narrower at the
package side due to mask defined pads. Please see attached image, or we can
put it up on the website.
At 12:09 PM 6/13/2005 -0400, Kerry McMullen wrote:
>Hi Technetters,
>Looks like we might have solved our BGA intermittent. Two boards were
>accidently dropped from a height of 12" (off a tray). The (4) 1028 ball
>BGAs popped off both boards! What is really interesting is that all the
>balls stayed on the boards, not on the device substrate. Any idea what
>would cause this? I know that you normally need a hammer to get a BGA off
>the board (unless you have an SRT). The device sees about 205 C at peak.
>
>Thanks in advance?
>Kerry
>
>---------------------------------------------------
>Technet Mail List provided as a service by IPC using LISTSERV 1.8e
>To unsubscribe, send a message to [log in to unmask] with following text in
>the BODY (NOT the subject field): SIGNOFF Technet
>To temporarily halt or (re-start) delivery of Technet send e-mail to
>[log in to unmask]: SET Technet NOMAIL or (MAIL)
>To receive ONE mailing per day of all the posts: send e-mail to
>[log in to unmask]: SET Technet Digest
>Search the archives of previous posts at: http://listserv.ipc.org/archives
>Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
>for additional information, or contact Keach Sasamori at [log in to unmask] or
>847-615-7100 ext.2815
>-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
Thank-you
Mumtaz
D/ 8165 - SMT Process Quality
Bldg. V244H
Voice (858)-882-1967
Fax (858)-882-3511
Page (858)-635-1180
email: [log in to unmask]
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
|
|