TECHNET Archives

February 2014

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Condense Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Sender:
X-To:
TechNet E-Mail Forum <[log in to unmask]>, GRIVON Arnaud <[log in to unmask]>
Date:
Tue, 11 Feb 2014 07:27:34 -0600
Reply-To:
TechNet E-Mail Forum <[log in to unmask]>, [log in to unmask]
Message-ID:
Subject:
From:
Douglas Pauls <[log in to unmask]>
Content-Transfer-Encoding:
quoted-printable
In-Reply-To:
Content-Type:
text/plain; charset="ISO-8859-1"
MIME-Version:
1.0
Parts/Attachments:
text/plain (155 lines)
Arnaud, 
You are welcome.  You can find this information in the newly published 
IPC-HDBK-830 Rev A, The Conformal Coating Handbook.   If I recall 
correctly, it is also found in IPC-HDBK-840, the Solder Mask Handbook. You 
will not find it in IPC-SM-840 (solder mask) or IPC-CC-830 (coating), 
because the problem is always the other guys fault.  If you are a solder 
mask guy, the fault is the coating.  If you are a coating guy, the fault 
is the mask.  The reason that it is not in the solder mask spec is that 
the surface energy is often more dependent on how the material was 
applied, processed and developed, more so than one of the material 
characteristics.  Since the intelligence of the solder mask processing is 
beyond the control of the solder mask vendor, it is not part of SM-840.

There is an ASTM standard from which the dyne pens are pulled: ASTM-D-2578 
? 08  Standard Test Method for Wetting Tension of Polyethylene and 
Polypropylene Films.  That ASTM method will tell you how to make your own 
calibrated alcohol solutions.  I find it easier to buy a set every year 
rather than having to store some of the chemicals year after year.

Doug Pauls



From:   GRIVON Arnaud <[log in to unmask]>
To:     <[log in to unmask]>
Date:   02/11/2014 02:06 AM
Subject:        Re: [TN] [COM] Solder Mask Surface Tension for Conformal 
Coating Adhesion
Sent by:        TechNet <[log in to unmask]>



Hello,

Thank you for the clear information provided.
As a supplement, I would be interested in someone could give the reference 
of the mentioned ASTM standard for surface energy measurement by Dyne 
Pens.
Also wondering why there is no IPC standard or guideline on this topic, as 
conformal coating adhesion on solder mask is a quite common concern within 
the industry.
It looks like indications given by Doug are acknowledged as good practice 
and therefore could be introduced within IPC standards.
Best regards,

Arnaud Grivon

-----Message d'origine-----
De : TechNet [mailto:[log in to unmask]] De la part de Lee Hitchens
Envoyé : mardi 4 février 2014 07:26
À : [log in to unmask]
Objet : Re: [TN] [COM] Solder Mask Surface Tension for Conformal Coating 
Adhesion

Hi Arnaud

I agree with Doug on this on using Dyne Pens although with no clean 
processing generally you are lucky if you can get close to the range of 
35-40! We tend to be working in the lower range of this. 

It's also solder resist / coating dependent. Don't dismiss the energy 
value out of hand immediately. There is no logic sometimes to selection. 
We found one case where we tried absolutely any coating we could find to 
stick to a solder resist and only one did. No idea why and none of the 
chemists could explain.


Best Regards

Lee Hitchens


-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Douglas Pauls
Sent: 03 February 2014 17:01
To: [log in to unmask]
Subject: Re: [TN] [COM] Solder Mask Surface Tension for Conformal Coating 
Adhesion

Arnaud,
I think you are asking about surface energy rather than surface tension. 
We use the readily available Dyne Pens which have solutions calibrated 
back to an ASTM standard.

I generally use this rule of thumb regardless of the coating used.

Under 30 dynes/cm:  Coating adhesion will be poor
30-35 dynes/cm:  Coating adhesion will be slightly better, but you can 
expect more frequent cases of delamination.
35-40 dynes/cm:  Coating adhesion generally good, but can have some 
periodic delamination or adhesion issues.
40-45 dynes/cm:  Coating adhesion is good and only rarely will you see 
delamination problems
45+ dynes.cm:  Good adhesion.

Of course, there will always be special cases but this is a good starting 
point.

Doug Pauls



From:   GRIVON Arnaud <[log in to unmask]>
To:     <[log in to unmask]>
Date:   02/03/2014 10:48 AM
Subject:        [TN] [COM] Solder Mask Surface Tension for Conformal 
Coating Adhesion
Sent by:        TechNet <[log in to unmask]>



Hello TechNet,

I would like to sense the best practices in terms of solder mask surface 
tension with respect to conformal coating adhesion :

-          Which standard/test method are you using?

-          Which requirement (e.g. minimum value in dyn/cm²) would you 
accept for the various CC types (acrylics, urethanes, silicone, parylene)?
Thanks in advance for the insights.
Best regards,

Arnaud Grivon


______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________



______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________



______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________

ATOM RSS1 RSS2