doesn't sound like he needs it overplated -- just filled to prevent
soldering problems.
At 05:32 PM 10/16/2008, Chezhian, Krishnan (Radhakrishnan) wrote:
>Hi Dave,
>
>This sounds like a VIPPO (Via In Pad Plated Over)Technology & we do this
>a lot for various customers. Yon need to plate the hole, fill it with
>epoxy & plate once again to cap the vias to form a pad, so the surface
>will be practically flat within +/-2.0mils....
>
>
>
>
>Thanks & Best Regards,
>
>Krishnan C
>
>Director Of Quality
>
>
>
>Sanmina-SCI Corporation (M) Sdn. Bhd.
>
>Sama Jaya Free Industrial Zone
>
>93450 Kuching, Sarawak, Malaysia.
>
>Tel: 60 82 363 000 Ext 1602
>
>Mobile: (6) - 012-8888-379
>
>Fax: 60 82 363 527
>
>E-mail: [log in to unmask]
>
>"It is easier to do a job right than to explain why you didn't."
>
>
>
>
>
>-----Original Message-----
>From: TechNet [mailto:[log in to unmask]] On Behalf Of Dave Connitt
>Sent: Thursday, October 16, 2008 10:35 PM
>To: [log in to unmask]
>Subject: Re: [TN] Problems with plating vias closed
>
>Hi Pete,
>This is a research/development project. The vias are currently tented,
>plus some are under a couple of 100 pin QFP's. I would have to move the
>vias out from under the FPGA's or risk solder balls once I untented
>them. Since this is a development project, I doubt they will spin the
>board again unless there is some other issue. We rarely wave solder
>boards anymore as there are very few thru hole parts on them anymore.
>The wave was a great way to fill vias with solder. Ah, the good old
>days..
>Dave Connitt CID+
>Printed Circuit Designer
>KDI Precision Products, Inc.
>A Wholly Owned Subsidiary of:
>L3 Communications
>3975 McMann Road
>Cincinnati, Ohio 45245
>Ph. 513- 943-2010 Fax 513-943-2288
>
>
>-----Original Message-----
>From: Pete Houwen [mailto:[log in to unmask]]
>Sent: Thursday, October 16, 2008 9:36 AM
>To: [log in to unmask]; Connitt, Dave @ KDI
>Subject: Re: Problems with plating vias closed
>
>Is this just a matter of closing the holes? Rather than having your PCB
>supplier try to plate the holes full, can you let them (partially) fill
>during soldering?
>
>---------------------------------------------------
>Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
>unsubscribe, send a message to [log in to unmask] with following text in
>the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
>(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
>Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
>posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
>archives of previous posts at: http://listserv.ipc.org/archives Please
>visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
>additional information, or contact Keach Sasamori at [log in to unmask] or
>847-615-7100 ext.2815
>-----------------------------------------------------
>
>
>
>CONFIDENTIALITY
>This e-mail message and any attachments thereto, is intended only
>for use by the addressee(s) named herein and may contain legally
>privileged and/or confidential information. If you are not the
>intended recipient of this e-mail message, you are hereby notified
>that any dissemination, distribution or copying of this e-mail
>message, and any attachments thereto, is strictly prohibited. If
>you have received this e-mail message in error, please immediately
>notify the sender and permanently delete the original and any copies
>of this email and any prints thereof.
>ABSENT AN EXPRESS STATEMENT TO THE CONTRARY HEREINABOVE, THIS E-MAIL
>IS NOT INTENDED AS A SUBSTITUTE FOR A WRITING. Notwithstanding the
>Uniform Electronic Transactions Act or the applicability of any
>other law of similar substance and effect, absent an express
>statement to the contrary hereinabove, this e-mail message its
>contents, and any attachments hereto are not intended to represent
>an offer or acceptance to enter into a contract and are not
>otherwise intended to bind the sender, Sanmina-SCI Corporation (or
>any of its subsidiaries), or any other person or entity.
>
>---------------------------------------------------
>Technet Mail List provided as a service by IPC using LISTSERV 15.0
>To unsubscribe, send a message to [log in to unmask] with following text in
>the BODY (NOT the subject field): SIGNOFF Technet
>To temporarily halt or (re-start) delivery of Technet send e-mail to
>[log in to unmask]: SET Technet NOMAIL or (MAIL)
>To receive ONE mailing per day of all the posts: send e-mail to
>[log in to unmask]: SET Technet Digest
>Search the archives of previous posts at: http://listserv.ipc.org/archives
>Please visit IPC web site
>http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
>information, or contact Keach Sasamori at [log in to unmask] or
>847-615-7100 ext.2815
>-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|