At 08.33 26/03/98 -0500, you wrote:
>Double Ditto.
>
>I tried using the gerber 274X format in Version 2.0 of PowerPCB and was
>also unable to read it into Gerbtool. I too have gone back to the 274D
>format.
>
>PADS are you listening ? Where's QA in times like this ?
>>
>>Regards, Greg.
>
>Gregory E. Bordash,
>Senior Technologist PCB Design
>ATI Technologies Inc.,
>33 Commerce Valley Drive East,
>Thornhill, Ontario, Canada, L3T 7N6
>Phone:(905) 882-2600 ext: 8370, Fax: (905) 882-9339
>Email: [log in to unmask]
>
>
>
>
>>----------
>>From: George Uptain[SMTP:[log in to unmask]]
>>Sent: Thursday, March 26, 1998 7:19 AM
>>To: [log in to unmask]
>>Subject: Re: [DC] PADS Gerber Output Question
>>
>>Ditto. I use Pads PowerPCB and must output in D then let CAM350 output
>>the X gerber files.
>>George W Uptain, Jr.
>>Austin Product Center of Schlumberger Oilfield Services
>>(512)331-3183
>>
>>> -----Original Message-----
>>> From: Ralph Garvin [SMTP:[log in to unmask]]
>>> Sent: Wednesday, March 25, 1998 7:54 PM
>>> To: [log in to unmask]
>>> Subject: Re: [DC] PADS Gerber Output Question
>>>
>>> Steve,
>>> The PADS 274x output is terrible. We have many problems with it and
>>> try it first with our viewer[CAM350] before sending it to the pcb
>>> production houses.[They also have had many problems with the files].
>>> Just make sure of your 274D format setting to get the correct number
>>> of
>>> digits.
>>> You would think that something as simple as the gerber output
>>> module
>>> would work correctly!!!!!
>>>
>>> Good Luck,
>>>
>>> Ralph Garvin
>>>
>>> ################################################################
>>> DesignerCouncil E-Mail Forum provided as a free service by IPC using
>>> LISTSERV 1.8c
>>> ################################################################
>>> To subscribe/unsubscribe, send a message to [log in to unmask] with
>>> following text in the body:
>>> To subscribe: SUBSCRIBE DesignerCouncil <your full name>
>>> To unsubscribe: SIGNOFF DesignerCouncil
>>> ################################################################
>>> Please visit IPC web site (http://jefry.ipc.org/forum.htm) for
>>> additional information.
>>> For the technical support contact Dmitriy Sklyar at [log in to unmask] or
>>> 847-509-9700 ext.311
>>> ################################################################
>>
>>################################################################
>>DesignerCouncil E-Mail Forum provided as a free service by IPC using
LISTSERV
>>1.8c
>>################################################################
>>To subscribe/unsubscribe, send a message to [log in to unmask] with following
>>text in the body:
>>To subscribe: SUBSCRIBE DesignerCouncil <your full name>
>>To unsubscribe: SIGNOFF DesignerCouncil
>>################################################################
>>Please visit IPC web site (http://jefry.ipc.org/forum.htm) for additional
>>information.
>>For the technical support contact Dmitriy Sklyar at [log in to unmask] or
>>847-509-9700 ext.311
>>################################################################
>>
>>
>
>################################################################
>DesignerCouncil E-Mail Forum provided as a free service by IPC using
LISTSERV 1.8c
>################################################################
>To subscribe/unsubscribe, send a message to [log in to unmask] with
following text in the body:
>To subscribe: SUBSCRIBE DesignerCouncil <your full name>
>To unsubscribe: SIGNOFF DesignerCouncil
>################################################################
>Please visit IPC web site (http://jefry.ipc.org/forum.htm) for additional
information.
>For the technical support contact Dmitriy Sklyar at [log in to unmask] or
847-509-9700 ext.311
>################################################################
>
>
Use Pcgerber work fine whit 274x generated from Pads.
Bye
+--------------------------+
| PcbAG |
| Pcb Design Service |
| Gianfranco Angiolini |
| Via Sofia 3 |
| 47831 Miramare di Rimini |
| Italy |
| Tel & Fax +39 541 371440 |
| Email [log in to unmask] |
+--------------------------+
################################################################
DesignerCouncil E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe: SUBSCRIBE DesignerCouncil <your full name>
To unsubscribe: SIGNOFF DesignerCouncil
################################################################
Please visit IPC web site (http://jefry.ipc.org/forum.htm) for additional information.
For the technical support contact Dmitriy Sklyar at [log in to unmask] or 847-509-9700 ext.311
################################################################
|