Concur with Kathy on all points . On the switching (contact points) we tested with no resistivity changes on carbon pill mounted in silicon pad action up to 50K cycles before we got down to copper . On the contact however ; once you wear the organic from top ; it does oxidize ; therefore unsuitable for more repeated low force low current switching . OK for edge con's in commercial applications , just. Which was the only reason why we keep NiAu ; which is not such a dream to solder ; as we have the silipad switching . Paul Klasek http://www.resmed.com -----Original Message----- From: Kathy Palumbo [mailto:[log in to unmask]] Sent: Tuesday, June 08, 1999 9:35 AM To: [log in to unmask] Subject: Re: [TN] Imersion Silver Charles, I did an extensive analysis (temperature cycling, vibration, humidity, lead pull testing, and cross sectioning) on completed assemblies with this coating on the PCB prior to approving it as an alternative coating to HASL. I found that the coating is a direct drop in replacement to HASL. In other words you can use the coatings interchangeable with no problems. The storage life is equivalent to HASL. The coating has no special handeling, or storage requirements. Keep in mind that if you are using the coating on your PCB as a contact point (i.e. a KEY BOARD) then the silver immersion coating is not the way to go (too thin). If you intend to solder to the coating, then it is not a problem. We have been using silver immersion as an alternative coating to HASL for more than 1 1/2 years with no problems. The wetting action of the solder to the pads was better than HASL coated PCB's, and the cross sectioning of several solder joints showed an even better fill of the solder under the leads than with HASL (which had quite a few voids). The biggest advantage was the elimination of bridging issues on fine pitch devices caused by the variance of the HASL deposit. We have virtually eliminated all of our bridging issues on fine pitch devices. This includes our PCMCIA Fax Modem product, which use to be our worse yeild and now is one of the best. Contact Steve Biegle with Alpha at (219) 922-7990. He has a lot of good data which you can review and use to set-up your own testing/evaluation process. If you have more specific questions regarding the testing I did you can contact me direct. Good Luck!! Kathy Palumbo Manufacturing Engineer Viking COmponents BUS.: (949) 643-7255 ----- Original Message ----- From: CharlesC <[log in to unmask]> To: <[log in to unmask]> Sent: 07 June 1999 14:33 Subject: [TN] Imersion Silver > Once again I need help. > I am looking for information on Alpha Metal's "AlphaLevel" Imersion silver > deposition. I have never built boards made with this process and would like to > know what experience anyone else may have had with this (good or bad ). The PWB > is mixed, some through hole mostly surface mount. I would especially like to > know about solderability and storage life. > > Thanks in advance. > > Charles Caswell > Process Lead, > Printed Circuit Board Dept. > Frontier Electronic Systems > > ################################################################ > TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c > ################################################################ > To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body: > To subscribe: SUBSCRIBE TechNet <your full name> > To unsubscribe: SIGNOFF TechNet > ################################################################ > Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information. > For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312 > ################################################################ > ################################################################ TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c ################################################################ To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body: To subscribe: SUBSCRIBE TechNet <your full name> To unsubscribe: SIGNOFF TechNet ################################################################ Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information. For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312 ################################################################ ################################################################ TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c ################################################################ To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body: To subscribe: SUBSCRIBE TechNet <your full name> To unsubscribe: SIGNOFF TechNet ################################################################ Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information. For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312 ################################################################ ################################################################ TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c ################################################################ To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body: To subscribe: SUBSCRIBE TechNet <your full name> To unsubscribe: SIGNOFF TechNet ################################################################ Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information. For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312 ################################################################