Mr Bisson, It is a guessing game to troubleshoot your process from sitting at my desk. There are many controllable and uncontrollable factors that causes solder ball formation. From based upon the info you supplied, you could try a few simple tests to narrow down causes of solder balls. 1. Use a fresh new solder paste and perform the test as you described. 2. Use a different mfg's NC paste and perform the test as you described. 3. Print and remove small portions of printed paste from inside areas of homeplate pads. And perform the test. This step basically removes squeezing-out effect of paste into masking area between pads when components are placed by a pick'n place machine. I believe this is what happened with 2 solder balls with homeplate. Homeplate will not completely eliminate this squeezing-out effect of solder paste during a component placement and the problem of solder balls gets worse with smaller chip components. V-design openings eliminate squeezing-out paste and at the same time leave enough paste area for component to hold on during placement cycles. We got no solder balls (very close to zero) since we started using V-design two years ago. regards Matthew Park NII Norsat International Inc. >>> Andre Bisson <[log in to unmask]> July 13, 1998 11:49 am >>> Mr. Park I read you article and I agree with you. I Understand that many people use the homeplate or equivalent shape. My question is, in the company I work before, I was using a reduction of 2 mils from the pad size using Water soluble paste and the result was no solder ball at all (really no solder ball). Now here we are using NC with the homeplate opening and sometime we still have some solder ball, same thing if we use the water soluble solder paste. I did conduct a test, just for fun, using a Topline board with (NC paste): - 2 rows with 1:1 (pad vs aperture) - 4 rows with 2 mils less - 4 rows with homeplate we assembled 8 boards and the result was respectively 122, 58 and 2 solder balls. So what is confusing me is why before I did not see solder ball and now I'm facing the solder ball problem? The answer is probably the placing equipment but why? Or maybe something else! Any others help will be appreciate. Thank you, At 10:18 98-07-13 -0700, Matthew Park wrote: >Mr. Bisson > >Please get hold of a March issue of Circuit Assembly. There is >an article that might help you with solderball problem. I am >available to discuss with you if you have further questions. > >regards > >matthew >SMT Manufacturing Engineer >NII Norsat International Inc. >604-597-6200, ext 254 > >>>> Andre Bisson <[log in to unmask]> July 10, >1998 10:40 am >>> >Hello, > >I need help from people who assembled board using NC solder >paste. I'm >presently facing some issues with solder balling after reflow >using NC paste. > >Our parameter are: > >NC paste >Good standard profile >Homeplate opening for chip (mpm printer) >Panasonic equipment for pick and place > >I'm use to run board with the following parameter with any solder >ball >(different company): > >Water paste >Good standard profile >Opening reduce by 0.002" than the pad size (mpm printer) >Contact system or Fuji Cp pick and place > >I will like to have comment from people who use NC paste and >don't have >this problem. If possible can you tell me why I have solder ball. I >take a >close look of the board and they are built with the ipc standard. > >Thank you very much, > > > >________________________________ > >Andre Bisson >Process Engineering >Matrox Electronic Systems >Tel.: (514) 969-6000 Ext: 2462 >E-mail: [log in to unmask] >________________________________ > >################################################################ >TechNet E-Mail Forum provided as a free service by IPC using >LISTSERV 1.8c >################################################################ >To subscribe/unsubscribe, send a message to >[log in to unmask] with following text in the body: >To subscribe: SUBSCRIBE TechNet <your full name> >To unsubscribe: SIGNOFF TechNet >################################################################ >Please visit IPC's web site (http://www.ipc.org) "On-Line >Services" section for additional information. >For technical support contact Hugo Scaramuzza at >[log in to unmask] or 847-509-9700 ext.312 >################################################################ > >################################################################ >TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c >################################################################ >To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body: >To subscribe: SUBSCRIBE TechNet <your full name> >To unsubscribe: SIGNOFF TechNet >################################################################ >Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information. >For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312 >################################################################ > > > ________________________________ Andre Bisson Process Engineering Matrox Electronic Systems Tel.: (514) 969-6000 Ext: 2462 E-mail: [log in to unmask] ________________________________ ################################################################ TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c ################################################################ To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body: To subscribe: SUBSCRIBE TechNet <your full name> To unsubscribe: SIGNOFF TechNet ################################################################ Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information. For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312 ################################################################ ################################################################ TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c ################################################################ To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body: To subscribe: SUBSCRIBE TechNet <your full name> To unsubscribe: SIGNOFF TechNet ################################################################ Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information. For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312 ################################################################