agree... not to use ACF as 1st choice.  rigid flex is much better  
with proper design and reinforcement to damp the vib.
  jk
On Jun 30, 2016, at 10:46 AM, John Burke wrote:

> Personally, for a high reliability application with high mechanical
> vibration I would not use ACF.
>
> As for the attachment methods for trials try this link:
>
> US6776859 (B1)  -  Anisotropic bonding system and method using dynamic
> feedback
> https://worldwide.espacenet.com/publicationDetails/biblio? 
> FT=D&date=20040817
> &DB=&locale=en_EP&CC=US&NR=6776859B1&KC=B1&ND=4
>
> Best regards,
>
> John
>
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Yuan-chia Joyce  
> Koo
> Sent: Thursday, June 30, 2016 4:25 AM
> To: [log in to unmask]
> Subject: Re: [TN] ACF bonding
>
> it depends on product and application method (how good is the your
> attachment), plus the moisture level and temp range of your product.
> some of the ACF swell when expose to the high RH, you will get high
> resistance joint (you need to take consideration in your system  
> design if
> intend used in un-controlled environment).
> my 1.4 cents
>         jk
> On Jun 29, 2016, at 4:03 PM, Ioan Tempea wrote:
>
>> Dear Technos,
>>
>> Any of you have experience with ACF bonding in high reliability
>> products? The application would be bonding flex to rigid PCB.
>>
>> A typical material datasheet is http://multimedia.3m.com/mws/media/
>> 407590O/3mtm-anisotropic-conductive-film-5363.pdf
>>
>> Thanks,
>>
>> Ioan Tempea, P. Eng.
>> Manufacturing Engineer, Satellite Systems
>>
>> [cid:[log in to unmask]]
>>
>> MacDonald, Dettwiler and Associates Corporation, 21025 Trans-Canada
>> Highway, Ste-Anne-de-Bellevue, QC, Canada H9X 3R2
>> Tel: +1-514-457-2150 x3556
>> www.mdacorporation.com<http://www.mdacorporation.com/>
>>
>> This e-mail, and any attachments, are intended solely for the use of
>> the intended recipient(s) and may contain legally privileged,
>> proprietary and/or confidential information. Any use, disclosure,
>> dissemination, distribution or copying of this e-mail and any
>> attachments for any purposes that have not been specifically
>> authorized by the sender is strictly prohibited. If you are not the
>> intended recipient, please immediately notify the sender by reply e-
>> mail and permanently delete all copies and attachments. This email is
>> for informational purposes only and shall not be interpreted to
>> authorize or conclude a binding agreement between MDA and any other
>> party unless this email contains or is accompanied by an express
>> written confirmation of MDA's intention to enter into a binding
>> agreement, such confirmation shall only be provided by an authorized
>> representative of MDA.
>>
>>
>> _____________________________________________________________________ 
>> _
>> This email has been scanned by the Symantec Email Security.cloud
>> service.
>> For more information please contact helpdesk at x2960 or
>> [log in to unmask]
>> _____________________________________________________________________ 
>> _
>
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud  
> service.
> For more information please contact helpdesk at x2960 or  
> [log in to unmask]
> ______________________________________________________________________
>
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud  
> service.
> For more information please contact helpdesk at x2960 or  
> [log in to unmask]
> ______________________________________________________________________


______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________