Hi Henry, What is the diameter of NPTH? Best regards, Gerry > Date: Tue, 10 Jun 2014 11:25:39 -0700 > From: [log in to unmask] > Subject: Re: [TN] Plating in non-plated holes - again > To: [log in to unmask] > > That's what I think, but we're getting push back from the supplier and I > was hoping to get more specific. > > Thanks. > > _____________________________________________________________________________________ > > > Henry Rekers P. Eng | Schneider Electric | Global Supply Chain | > Senior Manufacturing Engineer > Phone: +1-250-652-7100 ext. 7510 | Toll Free: +1-866-466-7627 ext. > 7510 | Fax: +1-250-544-2390 | > Email: [log in to unmask] | Site: > www.schneider-electric.com | Address: 2195 Keating Cross Road, > Saanichton, BC, Canada, V8M 2A5 > *** Please consider the environment before printing this e-mail > > > > From: > David Hillman <[log in to unmask]> > To: > <[log in to unmask]>, > Date: > 06/10/2014 10:08 AM > Subject: > Re: [TN] Plating in non-plated holes - again > Sent by: > TechNet <[log in to unmask]> > > > > Hi Henry - maybe I am making this too simple but if your drawing/design > data shows a nonplated thru hole, then having any plating in it, partial > or > complete, is a violation of the drawing and therefore a nonconformance. > > Dave > > > On Tue, Jun 10, 2014 at 10:26 AM, Henry Rekers < > [log in to unmask]> wrote: > > > Hey there technetters. A while back, I sent a message about enig > plating > > contamination in NON-plated holes. I've bounced it back to the board > > shop saying that it is unacceptable, but they claim it is due to 6012 > > 3.5.2 > > I also think it's unacceptable in the 4552 spec. The design > > documentation clearly states non-plated. It's not plated, just > partially > > plated. > > > > Any advice? > > > > Thanks. > > > > > _____________________________________________________________________________________ > > > > > > Henry Rekers P. Eng | Schneider Electric | Global Supply Chain | > > Senior Manufacturing Engineer > > Phone: +1-250-652-7100 ext. 7510 | Toll Free: +1-866-466-7627 ext. > > 7510 | Fax: +1-250-544-2390 | > > Email: [log in to unmask] | Site: > > www.schneider-electric.com | Address: 2195 Keating Cross Road, > > Saanichton, BC, Canada, V8M 2A5 > > *** Please consider the environment before printing this e-mail > > > > ______________________________________________________________________ > > This email has been scanned by the Symantec Email Security.cloud > service. > > For more information please contact helpdesk at x2960 or > [log in to unmask] > > ______________________________________________________________________ > > > > > ______________________________________________________________________ > This email has been scanned by the Symantec Email Security.cloud service. > For more information please contact helpdesk at x2960 or [log in to unmask] > ______________________________________________________________________ > > ______________________________________________________________________ > This email has been scanned by the Symantec Email Security.cloud service. > ______________________________________________________________________ > > > > > ______________________________________________________________________ > This email has been scanned by the Symantec Email Security.cloud service. > For more information please contact helpdesk at x2960 or [log in to unmask] > ______________________________________________________________________ ______________________________________________________________________ This email has been scanned by the Symantec Email Security.cloud service. For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________