ANSI/ESD S20.20-1999 included Humidity in Table 1 with the "recommended range" be ">30% Rh <70%". If used, that is still the recommendation, see ESD Handbook.. Note: In ANSI/ESD S20.20-2007 the table column heading was changed from "Recommended Range" to "Required Limit(s)" Here's what it says in the ESD Handbook ESD TR20.20 just updated in 2008. "5.3.16 Humidity Humidity is beneficial in all ESD control program plans. Contact and separation of dry materials generates greater electrostatic charges than moist materials because moisture provides conductivity that helps to dissipate charge. For this reason, ESD effects are most noticeable in the winter since heating systems reduce building environment moisture. Geographic location (desert vs. coastland) is also a major contributor to ambient conditions inside buildings. Any circumstance that results in a low relative humidity will permit a greater accumulation of electrostatic charges. Relative humidity above 30% in ESD protective areas is desirable as long as other adverse conditions are not created as a result of humidity levels. Generally speaking an upper limit of 70% is desirable to prevent corrosive effects on the metal portions of electronic devices and assemblies. Besides the increasing propensity to generate electrostatic charges on dry materials in general, performance of many ESD protective materials degrade. In fact, when exposed to low humidity conditions, some ESD protective materials become totally ineffective or become sources of electrostatic charges. Therefore, evaluation of ESD control materials should include performance testing in controlled environments at the lowest expected operating relative humidity level. Manufacturers of ESD protective materials should be able to provide performance data in regards to relative humidity. Likewise, materials should be tested in moderate humidity conditions as well to ensure they do not become "too conductive" and present a potential safety hazard to personnel working with substantial voltages. See the Personnel Safety section of this handbook for further guidance in this area. Humidity control in factories or physically large areas or buildings can be difficult and expensive. In smaller rooms or areas, it may be possible to use portable humidifiers to raise the immediate area humidity. However, in large facilities and factories the environmental systems many need to include steam generation and monitoring equipment to control humidity. This type of equipment is expensive to install and purchase especially in pre-existing facilities. To reduce the total cost impact, companies should consider the need for humidification equipment when planning new facility construction." Gene Felder [log in to unmask] -----Original Message----- From: TechNet [mailto:[log in to unmask]] On Behalf Of Guy Ramsey Sent: 2010 - 05 - 10 9:07 AM To: [log in to unmask] Subject: Re: [TN] ESD QUESTION ABOUT ANSI/ESD S202.20-2007 AND HUMIDITY MIL-HDBK-263 is still active. -----Original Message----- From: TechNet [mailto:[log in to unmask]] On Behalf Of Roberts, Jon (SA-1) Sent: Monday, May 10, 2010 11:42 AM To: [log in to unmask] Subject: [TN] ESD QUESTION ABOUT ANSI/ESD S202.20-2007 AND HUMIDITY In updated our ESD training, I noticed that the latest 20.20 drop humidity as a subject or requirement, which was under Paragraph 6.2.3.2 of ANSI/ESD S20.20 1999. Do any of you know why? Another spec used maybe? Thanks, Jon This communication is intended only for use by the addressee(s) named herein and may contain business confidential and/or legally privileged information. If you are not the intended recipient of this e-mail, you are hereby notified that any dissemination, distribution, disclosure or copying of this e-mail and its contents is strictly prohibited. If you have received this e-mail in error, kindly notify the sender by replying to this message. In addition, please permanently delete the message and any attachments without copying or disclosing the contents. Thank you for your cooperation. THIS DOCUMENT AND/OR SHIPMENT MAY CONTAIN COMMODITY ITEMS, SOFTWARE OR TECHNICAL DATA THAT IS CONTROLLED BY U.S. EXPORT LAW, AND MAY NOT BE EXPORTED OUTSIDE THE UNITED STATES OR TO NON U.S. PERSONS WITHOUT THE APPROPRIATE EXPORT LICENSE FROM EITHER THE U.S. DEPARTMENT OF STATE OR DEPARTMENT OF COMMERCE. ______________________________________________________________________ This email has been scanned by the MessageLabs Email Security System. For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________ --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 15.0 To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 ----------------------------------------------------- ______________________________________________________________________ This email has been scanned by the MessageLabs Email Security System. For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________ --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 15.0 To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 ----------------------------------------------------- ______________________________________________________________________ This email has been scanned by the MessageLabs Email Security System. For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________ --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 15.0 To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 -----------------------------------------------------