We use Creative Automation. The positive displacement pump gives excellent control of dot sizes, and can also be programmed to dispense beads or patterns. We have both the 3700 benchtop and 8300 inline models which we use for chipbonder. Their application engineers have always been very helpful, and other pump styles are available depending on the application. We have tips if we need to run 0402 or smaller, but currently discourage gluing parts this small in our DFM rules to make life easier. Whatever you pick, if you do not use it daily make sure it is easy to clean out or purge. For the Loctite 3621 chipbonder we only allow one month out of the fridge. If a syringe is not empty in that time it is disposed of. Exceeding shelf life and expiry dates will affect adhesion. Since we have replaced all but one of our wave solder machines with select solder we often only glue a few small parts per board and were finding that some heads were not using even 30cc's per month. Any manufacturer will run samples for you so you can make sure they are capable of meeting your requirements. http://www.creativedispensing.com/ Roger Mack P.Eng. Manufacturing Specialist Parker Hannifin Electronic Controls Electronic Controls Division 1305 Clarence Avenue Winnipeg, MB R3T 1T4 Canada direct 204 453 3339 x373 [log in to unmask] www.parker.com/ecd Syed Ahmad <[log in to unmask]> Sent by: TechNet <[log in to unmask]> 01-15-2010 14:44 Please respond to TechNet E-Mail Forum <[log in to unmask]>; Please respond to Syed Ahmad <[log in to unmask]> To [log in to unmask] cc Subject [TN] Dispensing system We are looking for a state-of-the-art dispensing system capable of making very fine features. We do not have a spec set yet but we are considering nScypt benchtop system. Is nScrypt the best choice? Does any one know of a competitive or better performing dispensing system to make very fine features? Any references for comparison or consideration will be appreciated. As we are a university research center, we can not limit the possible uses of this system but would welcome if a system has greater utility in the future. We may be using the system to dispense all kinds of materials as long as it can. Thanks. Syed. Syed Sajid Ahmad, Center for Nanoscale Science and Engineering (CNSE) North Dakota State University (NDSU) http://www.ndsu.edu/cnse/ --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 15.0 To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 ----------------------------------------------------- PLEASE NOTE: The preceding information may be confidential or privileged. It only should be used or disseminated for the purpose of conducting business with Parker. If you are not an intended recipient, please notify the sender by replying to this message and then delete the information from your system. Thank you for your cooperation. --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 15.0 To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 -----------------------------------------------------