Actually I can't figure out how you plate electrolytic Ni and Au after soldermask or why? Could you explain? Thank you, Eddie Rocha South Bay Circuits Hello Eddie, Thanks for your good idea. Can you explain how to process Electrolytic Ni and Au plating before LPI solder mask in detail? I can't figure out how it is done. Best regards, Linda Li -----Original Message----- From: Eddie Rocha [mailto:[log in to unmask]] Sent: Saturday, December 03, 2005 12:59 AM To: TechNet E-Mail Forum; Li, Linda Subject: Re: [TN] How to prevent solder mask peeling problem for ENIG+ENEG circuit boards I would have used the following sequence of processes: Electrolytic Ni & Au plating before LPI soldermask, etch the outer layer image, LPI soldermask, peelable mask (to protect the electrolytic gold features, then ENIG. I wouldn't expect soldermask adhesion problems with this approach. Thank you, Eddie Rocha South Bay Circuits Hello all, We have a design using ENIG plus ENEG surface finishing on circuit boards, ENIG is used for Al wire bonding, ENEG is used for Au wire bonding. We met 2 problems about this design. 1) We found solder mask peeling problem after aging the assembled circuit boards at 150 degree C for 2 hours. We contact the circuit board supplier and were told that because of 2 times UV exposure( 1 time is in solder mask exposure, the other is in ENIG process), the solder mask was apt to peel off. So far the supplier doesn't have any good method to solve this problem. Do you have any suggestions to solve this problem? Thanks. 2) During ENIG process, the gold is seeped onto the surface of copper pad that needs to be electrolytic gold plated. It's because of air bubble entrapped during dry film lamination. The supplier has changed the lamination speed, processed the panels in different direction, but still can't solve the problem. I am in urgent need of your expert advice . The circuit board fabrication process flow is as follows: >> solder mask printing>>dry film lamination>> UV exposure>>dry film development>>Electroless Nickel Immersion gold plating>>strip dry film resist>>Electrolytic nickel and gold plating>> Thanks for your help in advance! Best regards, Linda Li **************************************************************************************** Note: If the reader of this message is not the intended recipient, or an employee or agent responsible for delivering this message to the intended recipient, you are hereby notified that any dissemination, distribution or copying of this communication is strictly prohibited. If you have received this communication in error, please notify us immediately by replying to the message and deleting it from your computer. Thank you. **************************************************************************************** --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 ----------------------------------------------------- **************************************************************************************** Note: If the reader of this message is not the intended recipient, or an employee or agent responsible for delivering this message to the intended recipient, you are hereby notified that any dissemination, distribution or copying of this communication is strictly prohibited. If you have received this communication in error, please notify us immediately by replying to the message and deleting it from your computer. Thank you. **************************************************************************************** --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 ----------------------------------------------------- --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 -----------------------------------------------------