And anyway... it depends. Machine insert vs. hand insert and throw in solder process. Quick and uncomplicated isn't easy when it depends and the units are off by a factor of 10 or so. -Chris Bruce D Stilmack <[log in to unmask]> To: [log in to unmask] Sent by: TechNet cc: <[log in to unmask]> Subject: Re: [TN] FW: [TN] Component Lead to Hole Clearance 12/14/2005 04:45 PM Please respond to TechNet E-Mail Forum; Please respond to stilmack I'm with Phil. I've been trying to figure out the units Bruce Stilmack GDLS-TO Manufacturing Engineer (850) 574-4773 [log in to unmask] "Crepeau, Phil (Space Technology)" To <phil.crepeau@NGC [log in to unmask] .COM> cc Sent by: TechNet <[log in to unmask]> Subject Re: [TN] FW: [TN] Component Lead to Hole Clearance 12/14/2005 04:32 PM Please respond to TechNet E-Mail Forum <[log in to unmask]> ; Please respond to "Crepeau, Phil (Space Technology)" <phil.crepeau@NGC .COM> maybe nobody believed your hole sizes and wire diameters (unless they are in yards). -----Original Message----- From: TechNet [mailto:[log in to unmask]] On Behalf Of Victor G. Hernandez Sent: Wednesday, December 14, 2005 1:24 PM To: [log in to unmask] Subject: [TN] FW: [TN] Component Lead to Hole Clearance I did not get any responses the FIRST time perhaps the SECOND time is a charm. Victor, -----Original Message----- From: TechNet [mailto:[log in to unmask]] On Behalf Of Victor G. Hernandez Sent: Tuesday, December 13, 2005 8:05 AM To: [log in to unmask] Subject: [TN] Component Lead to Hole Clearance Fellow TechNetters: Can someone shared their experience with calculating lead to hole ratio as per IPC-2222 Figure 9-3? I have a cross section in which I suspect the lead diameter cause insufficient solder fillet. I need a QUICK GUIDE to determine this relationship without being complicated. Rough drill size: 0.000376 Plated barrel size: 0.003432 Lead size: 0.002047 Victor. --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 ----------------------------------------------------- --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 ----------------------------------------------------- --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 ----------------------------------------------------- This is an e-mail from General Dynamics Land Systems. It is for the intended recipient only and may contain confidential and privileged information. No one else may read, print, store, copy, forward or act in reliance on it or its attachments. If you are not the intended recipient, please return this message to the sender and delete the message and any attachments from your computer. Your cooperation is appreciated. --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 ----------------------------------------------------- --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 -----------------------------------------------------