Richard, I wrote recently saying how we at Nielsen Media Research match up the BOM and assembly drawing as Phil suggests below. I also got an em from Rainer saying you shouldn't match them. When I came to NMR 15 years ago, they had a very informal system, so I tried to implement the exact system you and he suggest as I grew up at the same Honeywell plant he's at. Shortly after, we changed from that system to our present method at the request of all four of our CM's. Even though it's definitely more effort to roll the revision all the way to the top, all agreed it was the only way to ensure notification of the change. 80% of our metering equipment is low volume, high mix, and frequently revised. We're still using those four CM's and now have three more in China building our stuff and have no problems implementing changes with this method. We only advance revisions as low as is necessary, but always all the way to the top level, even if it's something as insignificant as correcting a spelling error. We do define effectivities very carefully on our ECO's so our CM's and repair depot know what impacts them uniquely. What I'm really saying is you need to design or modify your configuration management system to support your manufacturing floor (or CM) as much as you possibly can. No matter what system you use, the engineers will complain as it's in their DNA, but you should make it match the needs of the guy who builds it and repairs it. Bob -----Original Message----- From: TechNet [mailto:[log in to unmask]] On Behalf Of Stadem, Richard Sent: Monday, October 10, 2005 9:20 AM To: [log in to unmask] Subject: Re: [TN] Assembly Documentation Question I disagree. Most places I have worked have separate BOM and assembly drawing revisions. The documents are independent of each other. The reason for this is because the BOM is seldom a static document. It undergoes changes on a regular basis. Every Engineering Change Notice/Order has a significant cost. For every ECN someone needs to update the BOM, update the configuration list, update the schematic drawing, etc. etc. Demanding that the assembly drawing maintain the same revision as the BOM means that you have just doubled the price of every ECN. Unfortunatly the schematic must be updated every time the BOM changes, as the component values must be updated on the schematic. Adding the AD to the list just adds cost. Look at it this way; there is a circuit that is attached to the assembly. Changing something on the circuit does not change the assembly. If changing something on the circuit demands a change to the assembly, then the assembly revision should be updated as well. But if changing something in the circuit does not change the assembly configuration, then no change need be made to the assembly drawing, thus no change to the revision. I....must learn...to accept....change....because...nothing.....ever....remains...the...same. Must....learn..to manage...methods...that...make sense....economically. -----Original Message----- From: TechNet [mailto:[log in to unmask]] On Behalf Of Phil Nutting Sent: Friday, October 07, 2005 12:23 PM To: [log in to unmask] Subject: Re: [TN] Assembly Documentation Question Michael, My experience and preference is to have the BOM and assembly drawing match in revision. If they don't match who is going to maintain a matrix explaining what document goes with another document. Does your BOM call out the revision of the assembly? If so wouldn't you have to uprev the BOM to reflect the change in revision of the assembly print? We experimented with making "dash" prints where we started with a "generic" design with a -X suffix and then for subtle changes made -1, -2, etc. assemblies but all based upon the -X print. You wouldn't believe the confusion this caused at outsource vendors and our revisions. Imaging the problem when the assembly print and BOM revs do not match. I... Can... Not... Change! Must... Do... It... the...way... I... Have... always... Done... It! Wow that was close. Phil -----Original Message----- From: TechNet [mailto:[log in to unmask]] On Behalf Of Michael Kuczynski Sent: Friday, October 07, 2005 12:19 PM To: [log in to unmask] Subject: [TN] Assembly Documentation Question The company I work for is going thru some documentation change discussions. Below are the documents that are revisable. (The parts list contains all the IC's, cap, res. etc. and documents.) The feedback I'm getting is the the parts list and the assembly drawing should ALWAYS be the same revision (becasue thats the way its always been). Everywhere I've every worked, these are independent documents. Here are my scenerio case: (All documentation released at Rev. A) Scenerio (Rev: B): A part number change, of a 1K, 5% resistor to a 1K, 1% resistor. In this case, the part list and schematic would change, but it has no effect on the assembly (because no part number or value is on the assembly drawing). PL1234567-1 Rev: B Parts List AW1234567 Rev: A Assy Dwg DS1234567 Rev: A Drill Dwg PC1234567 Rev: A Artwork PA1234567 Rev: B Schematic Scenerio (Rev: C): The length of the screw holding the stiffener bar is changed from 3/8 in. to 1/2 in. The change is to the parts list only, the assembly drawing stays the same. (no 3D view or side view) PL1234567-1 Rev: C Parts List AW1234567 Rev: A Assy Dwg DS1234567 Rev: A Drill Dwg PC1234567 Rev: A Artwork PA1234567 Rev: B Schematic The current discussion and question is; -Can the parts list be independently revisible, from the assembly drawing? -What do most of the assembly houses usually like? Thanks for any response to this question. --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 ----------------------------------------------------- [log in to unmask] --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 ----------------------------------------------------- --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 ----------------------------------------------------- --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 -----------------------------------------------------