We use Cadence Allegro, "IPC-356" can be extracted during output. On the fab drawing we have a note: #12. Perform Electrical netlist testing on all PWBS per IPC-D-356 netlist provided. If netlist provided does not match artwork during fabrication front end job setup, stop job, and call Catapult. We do up to 30 layer, low volume. I would hate to build anything that didn't match. All I got to say is "Time and money" dave Roland Jaquet wrote: >It sounds so good.. > >Unfortunately, so little companies are even conscious of the advantage of >the IPC-356.. and if the CAD software does not yet automatically supply it, >please request it. > >Any idea of the percentage of PCB orders that are using IPC-356 ??? > >Can PCB manufacturers give an idea of the percentage of jobs they get with >it??? > >I seen Electrically Tested PCB's that were missing an inner layer... because >they used the Golden board approach... > > >Very Best regards >Rol@nd > >www.PCBspecialist.com >T +41-22-880-0405 F +41-22-880-0409 Mob +41-79-203-3723 > > >-----Message d'origine----- >De : TechNet [mailto:[log in to unmask]] De la part de Dave Seymour >Envoyé : mercredi, 6. avril 2005 15:57 >À : [log in to unmask] >Objet : Re: [TN] Golden Board Electrical test > >To add Marsal response. > >The golden board goes through shorts and opens test, >visual QC and then passed. This board the becomes the >reference that all other boards are then check by. > >However, this not an electrical netlist test. >If the generated Gerber artwork had an error during output at >the design phase, the artwork produced may not match the intended >schematic. > >At this point all boards match each other and are declared "good", >But, the boards don't match the schematic. > >This is the reason for the "IPC-356" netlist being included with all >jobs going to fabrication. All designs that leave our shop must have >an extract IPC-356 netlist for the fab shop to verify artwork shipped. > >Hope this helps. >dave > > > > >Marsal Tampubolon wrote: > > > >>Hi Suganthi.. >>In other words, golden board also call as KGB >>(Known Good board ). Sometimes also call as reference >>board. Meaning it is the sample board that being >>pass test if there is electrical test conducted or >>pass visual test. This board will using for set >>up tester before run to mass production test or during >>comparison for troubleshoot board defect from the same >>model. >> >>**************************************************** >>Regards... >>Marsal GM Tampubolon. >> >> >>|---------+----------------------------> >>| | Suganthi | >>| | <suganthi@CG-CORE| >>| | EL.COM> | >>| | Sent by: TechNet | >>| | <[log in to unmask]>| >>| | | >>| | | >>| | 06-04-05 04:30 PM| >>| | Please respond to| >>| | Suganthi | >>| | | >>|---------+----------------------------> >> >>--------------------------------------------------------------------------- >> >> >-------------------| > > >> | >> >> >| > > >> | To: [log in to unmask] >> >> >| > > >> | cc: >> >> >| > > >> | Subject: [TN] Golden Board Electrical test >> >> >| > > >>--------------------------------------------------------------------------- >> >> >-------------------| > > >> >> >> >> >>Dear All, >> >> >> >> please explain me what is "Golden Board" electrical test >> >> >> >>Thanks and Regards >> >> >>--------------------------------------------------- >>Technet Mail List provided as a service by IPC using LISTSERV 1.8e >>To unsubscribe, send a message to [log in to unmask] with following >>text in >>the BODY (NOT the subject field): SIGNOFF Technet >>To temporarily halt or (re-start) delivery of Technet send e-mail >>to [log in to unmask]: SET Technet NOMAIL or (MAIL) >>To receive ONE mailing per day of all the posts: send e-mail to >>[log in to unmask]: SET Technet Digest >>Search the archives of previous posts at: >>http://listserv.ipc.org/archives >>Please visit IPC web site >>http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional >>information, or contact Keach Sasamori at [log in to unmask] or >>847-615-7100 ext.2815 >>----------------------------------------------------- >>Sug >> >>--------------------------------------------------- >>Technet Mail List provided as a service by IPC using LISTSERV 1.8e >>To unsubscribe, send a message to [log in to unmask] with following text in >>the BODY (NOT the subject field): SIGNOFF Technet >>To temporarily halt or (re-start) delivery of Technet send e-mail to >> >> >[log in to unmask]: SET Technet NOMAIL or (MAIL) > > >>To receive ONE mailing per day of all the posts: send e-mail to >> >> >[log in to unmask]: SET Technet Digest > > >>Search the archives of previous posts at: http://listserv.ipc.org/archives >>Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 >> >> >for additional information, or contact Keach Sasamori at [log in to unmask] or >847-615-7100 ext.2815 > > >>----------------------------------------------------- >> >> >> >> >> >> > >-- >Dave Seymour, CID+ >Catapult Communications Inc. >800 Perimeter Park Dr, Suite A >Morrisville, NC 27560 > >Direct: (919)653-4249 >Main: (919)653-4180 >Fax: (919)653-4297 > >[log in to unmask] > >--------------------------------------------------- >Technet Mail List provided as a service by IPC using LISTSERV 1.8e >To unsubscribe, send a message to [log in to unmask] with following text in >the BODY (NOT the subject field): SIGNOFF Technet >To temporarily halt or (re-start) delivery of Technet send e-mail to >[log in to unmask]: SET Technet NOMAIL or (MAIL) >To receive ONE mailing per day of all the posts: send e-mail to >[log in to unmask]: SET Technet Digest >Search the archives of previous posts at: http://listserv.ipc.org/archives >Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 >for additional information, or contact Keach Sasamori at [log in to unmask] or >847-615-7100 ext.2815 >----------------------------------------------------- > >--------------------------------------------------- >Technet Mail List provided as a service by IPC using LISTSERV 1.8e >To unsubscribe, send a message to [log in to unmask] with following text in >the BODY (NOT the subject field): SIGNOFF Technet >To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) >To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest >Search the archives of previous posts at: http://listserv.ipc.org/archives >Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 >----------------------------------------------------- > > > > -- Dave Seymour, CID+ Catapult Communications Inc. 800 Perimeter Park Dr, Suite A Morrisville, NC 27560 Direct: (919)653-4249 Main: (919)653-4180 Fax: (919)653-4297 [log in to unmask] --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815 -----------------------------------------------------