I would agree with that. 1 up with panelized drawing. -Rich -----Original Message----- From: Damon DeSilva [mailto:[log in to unmask]] Sent: Monday, July 12, 2004 2:52 PM To: [log in to unmask] Subject: Re: [TN] Question about panelization Preferred would be 1 up with panelization drawing. I'm not familiar with the assembly, but I believe 1/4" would be the lowest dimension you would want. Typical is 1/2" Regards, Damon A. DeSilva Engineering Manager Lazer-Tech Ltd. PH#(416)291-7727 EXT:271 FAX(416)291-0325 [log in to unmask] -----Original Message----- From: TechNet [mailto:[log in to unmask]]On Behalf Of John Foster Sent: Monday, July 12, 2004 2:32 PM To: [log in to unmask] Subject: [TN] Question about panelization I have been doing a lot of layouts lately of very small boards. These boards require panelization. I was wondering if I could get a idea of whether fabricators prefer to get gerber that is already panelized or whether they prefer to just get the one up gerber with a drawing that shows the panelization. Also I was wondering at what board size does it become a pain for assembly. I always try to put .250 inch manufacturing rails on boards for the conveyors. I have been doing a lot of boards on the 1" x 2" size. Any input would be appreciated. Thank You --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315 ----------------------------------------------------- --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315 ----------------------------------------------------- --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315 -----------------------------------------------------