One thing I have seen in X-ray inspection of BGA parts is small solder balls where the paste has reflowed but not attached to the pad or part and becomes a loose 'B-B' (ammo for an air rifle) under the part that could become a potential short if not cleaned out from under it. Usually the technician can used compressed air to blow the loose solder ball out from under the part before running the parts through the aqueous wash. If you did not tent the vias under the part they might be potential shorting points for solder balls or other debris so as a rule I always opt for tenting the vias, unless specific ones are used as test points like Andy points out. Bill Brooks PCB Design Engineer , C.I.D., C.I.I. -----Original Message----- From: Kowalewski, Andy [mailto:[log in to unmask]] Sent: Friday, October 24, 2003 8:49 AM To: [log in to unmask] Subject: Re: [DC] Cleaning of via holes under components Debris is one issue, but possibly a more important one is the via filling with solder during wave soldering, forming a 'crown' on the primary side and possibly touching a metal part of the component over the via hole, causing a short circuit. That's particularly a problem with a lot of small chip components, as well as a lot of RF metal-cased components, that are mounted over the via. Via tenting is an established practice, and there are few reasons not to tent. It's foolproof tenting both sides, but might need via plugging if the solder mask is a thin photoimagable type and the via hole is bigger than about 0.3mm. Of course the picture gets a little more complicated if the via is used as a test point for probing. I know some people tent only the non-probed side, but I don't like doing that - it becomes a trap for all sorts of nasty chemicals which can give long term reliability problems. Andy K. Sychip Inc Office (972) 202 8852 -----Original Message----- From: Chris Robertson [mailto:[log in to unmask]] Sent: Friday, October 24, 2003 10:01 AM To: [log in to unmask] Subject: [DC] Cleaning of via holes under components There as been many an occasion debris or foreign matter in a via causing problems. I personally mask over all vias, and have never had a problem, but have a question. Yes, debris in a via and being under a pad, in encapsulated in solder or plating etc. is a reasonable question to ask. Could there be a problem, but my question is; Isn't this a cleanliness issue? Is it just a fact that regardless of the manufacturer that debris or such is a fact and not just a manufacturer issue. Is it that, yes it may be just a manufacturer issue, but there is no accountability before assembly and we can't just count on the board to be clean. Or is it the time between manufacturing and assembly that we have to worry about debris? I've never had an issue with debris in a via, and I don't know if I have good manufacturers or that my traces/circuits have never been that critical. Chris Robertson [log in to unmask] <mailto:[log in to unmask]> ----- Original Message ----- From: Paul <mailto:[log in to unmask]> Baine To: [log in to unmask] <mailto:[log in to unmask]> Sent: Friday, October 24, 2003 9:30 AM Subject: [TN] Cleaning of via holes under components Hello, One of our Design Engineers is designing a surface mount PCB assembly and would prefer not to have the via holes solder mask tented. However, he is concerned that, if he does not call up solder mask tenting on his bare PCB drawing, foreign matter could find its way into a via hole and, if a component (e.g. an IC) was mounted over the via hole, the foreign matter might not be removed during the cleaning process. Has anyone had experience with this situation? I would appreciate any help you could give me. Thanks very much in advance. Paul Baine Q.A. Manager C-Tech Ltd. Cornwall, Ontario, Canada --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] <mailto:[log in to unmask]> with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask] <mailto:[log in to unmask]> : SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask] <mailto:[log in to unmask]> : SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives <http://listserv.ipc.org/archives> Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 <http://www.ipc.org/contentpage.asp?Pageid=4.3.16> for additional information, or contact Keach Sasamori at [log in to unmask] <mailto:[log in to unmask]> or 847-509-9700 ext.5315 ----------------------------------------------------- ---------------------------------------------------------------------------- ----- DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 1.8d To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF DesignerCouncil. To set a vacation stop for delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL Search previous postings at: www.ipc.org > On-Line Resources & Databases > E-mail Archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315 ---------------------------------------------------------------------------- ----- ---------------------------------------------------------------------------- ----- DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 1.8d To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF DesignerCouncil. To set a vacation stop for delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL Search previous postings at: www.ipc.org > On-Line Resources & Databases > E-mail Archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315 ---------------------------------------------------------------------------- ----- --------------------------------------------------- Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315 -----------------------------------------------------