I'm going to add another 1c's worth here over the 2c's worth I posted a moment ago. I like to check torques at the end of a run just to be sure that nothing has 'settled' or contracted since the assembly was carried out. It also ensures that an operator hasn't missed any. Peter Earl Moon <[log in to unmask]> 06/09/2002 02:02 AM Sent by: TechNet <[log in to unmask]> Please respond to "TechNet E-Mail Forum."; Please respond to pod To: [log in to unmask] cc: (bcc: DUNCAN Peter/Asst Prin Engr/ST Aero/ST Group) Subject: Re: [TN] Torque Inspections That's one way. Earl ----- Original Message ----- From: "Kathy Kuhlow" <[log in to unmask]> To: <[log in to unmask]> Sent: Thursday, September 05, 2002 11:03 AM Subject: [TN] Torque Inspections I was curious how are torque requirements for hardware are being confirmed? If a particular piece of hardware has a torque requirement of 12in/lbs how would the verification of that piece of hardware be done? Do you use a torque driver at the same in/lbs or back off of the torque range or look for loose(gap only)? TIA Kat ---------------------------------------------------------------------------- ----- Technet Mail List provided as a free service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/html/forum.htm for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315 ---------------------------------------------------------------------------- ----- --------------------------------------------------------------------------------- Technet Mail List provided as a free service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/html/forum.htm for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315 --------------------------------------------------------------------------------- [This e-mail is confidential and may also be privileged. If you are not the intended recipient, please delete it and notify us immediately; you should not copy or use it for any purpose, nor disclose its contents to any other person. Thank you.] --------------------------------------------------------------------------------- Technet Mail List provided as a free service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/html/forum.htm for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315 ---------------------------------------------------------------------------------