Thank you for the respose Wanner, it is appreciated!
______________________________ Forward Header __________________________________
Subject: [TN] SMD solder voids
Author: Wanner Bernhard <[log in to unmask]> at Internet
Date: 11/12/1999 3:19 PM
IPC-A-610B (issued January 96), chapter 10, covers SMD solder joints, but
only for externally view. 4.2 (fig. 4-15) says: "(...) blow holes, pinholes
(...) are nonconforming process indicators (...)".
But a "nonconforming process" is not the same as a "nonconforming product",
therefore see foreword ("Nonconforming Process Indicator Condition"): "
(...) not affect the form, fit & function of a product (...) the product
affected will be dispositioned Use as is (...) if the company does not have
a documented Process Control system (customer approved, J-STD-001, sic!),
then all Nonconforming Process Indicators must be treated as Nonconforming
Defects (...)" voila!
Enough collective wisdom?
Sometimes I have the impression plane IPC should reevancelicate the short
basic principles of the requirement flowdown for electronic assemblers. The
backbone would be:
* J-STD-001B (soon C) for soldered electronic assemblies.
Based on J-STD-001B (as backbone), table 3-1 - and the up-dates
during the meanstime - for rigid pwb's the bones could be defined as:
* IPC-2221 and IPC-2222 (rigid) and/or(?) IPC-D-279 (SMT) for
design/layout,
* IPC-6011 and IPC-6012 and IPC-A-600E for PWB manufacturer (to refer
on the purchasing spec's!)
Other specifications (fishbones) would be adressed by the standard-inherent
requirement flowdown (IPC-SM-782, IPC-4101, IPC-SM-840, ev. IPC-CC-830 et
al)
Bernhard, near Zürich (for you: Zurich)
PS, to the guru's: there is a litte conflict between IPC-6012 3.11.1 (" ..
0.1% ..") and Appendix A, p. 27, 3.11.1 (".. 9.01% ..), it isn't?
-----Ursprüngliche Nachricht-----
Von: Automatic digest processor [SMTP:[log in to unmask]]
Gesendet am: Freitag, 12. November 1999 07:00
An: Recipients of TechNet digests
Betreff: TechNet Digest - 11 Nov 1999 (#1999-367)
At 10:45 AM 11/11/99 -0500, you wrote:
> Hi gang,
> We are cross-sectiong some solder joints, and are seeing
some
> voiding inside the joint itself, that appears to be "air
pockets" that
> were inside the joint when reflowed. There is no visible
indication
> externally of any voiding, but it is fairly prevalent inside
various
> component solder joints when cross-sectioned.
>
> I cannot find criteria or mention of this in the
specifications I
> have. ANSI/IPC-A-610A shows voiding criteria for thru-hole
components,
> but none for SMD.
>
> Does anyone have knowledge they can share on this topic? Is
there a
> spec on internal SMD joint voiding available? Do you guys and
gals see
> this occasionally in your joints?
>
> Please, enlighten me with your collective wisdoms!
> TIA!
>
> Jeff Hempton
> United Technologies Electronic Controls
##############################################################
TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
##############################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text
in
the body:
To subscribe: SUBSCRIBE TECHNET <your full name>
To unsubscribe: SIGNOFF TECHNET
##############################################################
Please visit IPC web site (http://www.ipc.org/html/forum.htm) for additional
information.
If you need assistance - contact Gayatri Sardeshpande at [log in to unmask] or
847-509-9700 ext.5365
##############################################################
##############################################################
TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
##############################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in
the body:
To subscribe: SUBSCRIBE TECHNET <your full name>
To unsubscribe: SIGNOFF TECHNET
##############################################################
Please visit IPC web site (http://www.ipc.org/html/forum.htm) for additional
information.
If you need assistance - contact Gayatri Sardeshpande at [log in to unmask] or
847-509-9700 ext.5365
##############################################################
|