Hey Ed,
Perhaps you should post this to the Designers Council forum.
There are 7 or 8 hundred subscribers who may be more suited to this
question.
I unfortunately don't do BGA.
Hope it helps
FNK
Frank N Kimmey C.I.D.
EM Designer
C&K Systems, Inc.
916-353-5366
[log in to unmask]
> ----------
> From: [log in to unmask][SMTP:[log in to unmask]]
> Reply To: TechNet E-Mail Forum.;[log in to unmask]
> Sent: Tuesday, April 13, 1999 4:14 PM
> To: [log in to unmask]
> Subject: Re: [TN] BGA and micro-BGA consumption distribution
>
> Greetings, all!
>
> I hope I'm not asking too much in the below prior post, but I'm sure
> those
> who use (or are planning to) BGA/uBGA will benefit from this data...
> HOWEVER... I've only received 3 responses in a week. What this implies
> is of
> the 1700 or so technet participants, only 3 of them are using
> BGA/uBGA...that's only 0.17%! I believe this is not an accurate
> representation. Of course, I have a "hidden agenda" in asking for your
> input
> as I do need this data for a project I'm working on, but I am willing
> to
> share the results... fair deal?
>
> Any and all input, no matter how "inaccurate" will be greatly
> appreciated.
>
> Ed
>
> > -----Original Message-----
> > From: [log in to unmask] [SMTP:[log in to unmask]]
> > Sent: 8 de Abril de 1999 12:27
> > To: [log in to unmask]
> > Subject: [TN] BGA and micro-BGA consumption distribution
> >
> > Hi again fellow Techies,
> >
> > I am trying to determine an approximate useage distribution for
> > various BGA
> > and micro-BGA components across the board...so if you would be
> willing
> > to
> > help:
> >
> > Please identify package type and percentage (approximate) of each
> type
> > that
> > you consume, i.e., "Of all the BGA & uBGA, 50% are PBGA352, 25% are
> > CBGA625
> > and 25% 56 ball uBGA". Accuracy of distribution estimates are not
> > critical
> > (+/- 15% would be more than adequate).
> >
> > To minimize "technet traffic" please respond directly to the email
> > address
> > below. Once all responses are received, I will report findings back
> to
> > Technet for anyone who may have use for such info.
> >
> > Thank you all in advance for your help,
>
>
> Ed Popielarski
> QTA Machine
> 10 Mc Laren, Suite D
> Irvine, Ca. USA 92618
> Ph: (949)581-6601
> Fx: (949)581-2448
> E-Mail: [log in to unmask]
> http://www.qta.net
>
> ################################################################
> TechNet E-Mail Forum provided as a free service by IPC using LISTSERV
> 1.8c
> ################################################################
> To subscribe/unsubscribe, send a message to [log in to unmask] with
> following text in the body:
> To subscribe: SUBSCRIBE TechNet <your full name>
> To unsubscribe: SIGNOFF TechNet
> ################################################################
> Please visit IPC's web site (http://www.ipc.org) "On-Line Services"
> section for additional information.
> For technical support contact Hugo Scaramuzza at [log in to unmask] or
> 847-509-9700 ext.312
> ################################################################
>
################################################################
TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe: SUBSCRIBE TechNet <your full name>
To unsubscribe: SIGNOFF TechNet
################################################################
Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information.
For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312
################################################################
|
