OK
>Date: Fri, 19 Feb 1999 10:32:45 GMT
>Reply-To: "TechNet E-Mail Forum." <[log in to unmask]>,
> Edward Brunker <[log in to unmask]>
>From: Edward Brunker <[log in to unmask]>
>Subject: Re: [TN] TechNet: confirmation required (6F2282)
>To: [log in to unmask]
>
>ok
>
>______________________________ Reply Separator
_________________________________
>Subject: TechNet: confirmation required (6F2282)
>Author: "L-Soft list server at IPC (1.8c)" <[log in to unmask]> at
INTERNET
>Date: 19/02/99 04:21
>
>
>The TechNet list has been configured to request explicit confirmation
of all
>messages posted to the list, for security reasons. You must now
confirm that
>the message enclosed below did originate from you. To do so, simply
reply to
>the present message and type "OK" (without the quotes) in the text
of your
>message. If this does not work, or if the message did NOT originate
from you,
>contact the list owner for assistance.
>
>------------------ Original message (ID=6F2282) (91 lines)
--------------------
>Received: from simon.ipc.org by jefry.ipc.org (LSMTP for Windows NT
v1.1a) with
>TP id <[log in to unmask]>; Fri, 19 Feb 1999 4:21:24 -0600
>Received: from mailgate.psion.com by simon.ipc.org via ESMTP
(951211.SGI.8.6.12.
>TCH1502/940406.SGI)
> for <[log in to unmask]> id EAA01676; Fri, 19 Feb 1999 04:10:17
-0800
>Received: from smtpgate.psion.com (smtpgate.psion.com [194.129.2.239])
> by mailgate.psion.com (2.5 Build 2640 (Berkeley 8.8.6)/8.8.4)
with
> SMTP id KAA00291 for <[log in to unmask]>; Fri, 19 Feb 1999
10:10:54 GMT
>Received: from ccMail by smtpgate.psion.com (ccMail Link to SMTP
R8.20.00.25)
> id AA919420092; Fri, 19 Feb 1999 10:28:17 GMT
>Message-Id: <[log in to unmask]>
>X-Mailer: ccMail Link to SMTP R8.20.00.25
>Date: Fri, 19 Feb 1999 10:19:56 GMT
>From: "Edward Brunker"<[log in to unmask]>
>To: <[log in to unmask]>
>Subject: Re[2]: [TN] Squeegee Speed
>MIME-Version: 1.0
>Content-Type: text/plain; charset=US-ASCII
>Content-Transfer-Encoding: 7bit
>Content-Description: "cc:Mail Note Part"
>
>
>
>>The factorinfluencing this effect is how stencil gaskets to the board
and
>>you may need to look as points such as : Board finish
>
>>Regards
>>Edward Hale
>
>
> I find this aspect intersting. Resist height is always more than
the
> plated copper height. For all alternative finishes with LPI, in my
> experience. The resist over traces leading to pads brings the
resist
> up even more. The dome on HASL boards will protrude above, but
only
> for a portion of the pad, the edges still remain lower.
> Does anyone spec the resist height to be less than the pads?
> So stencils rest on the resist leaving 10 - 30 microns of free
space
> underneath.
>
>
> Regards
> Edward Brunker
>
>
>>Evenin' all!
>>
>> My question is this: My stencil printer operator has said
that he
>>has to
>>wipe our 6-mil stencil each pass to get the paste in the 20-mill pitch
>>aperatures for a QFP to release well. We are using Amtech NC-559 type
3
>>paste with 89.5% metal. The paste is not old. I considered using
type 4
>>paste, which has a much finer powder in it. I was told by Amtech that
this
>>finer powder paste will pack more densly into the aperatures and I
could get
>>some bridging, unless I order a new stencil with aperature reductions.
Our
>>squeegee speed is 0.6 inches/s, or 15mm/s. Is this too slow? Amtech
>>suggested that at this slow speed, the paste could be rising out of
the
>>aperature, as if someone pressed on a wet sponge and it rose back to
its
>>original shape. What is a good squeegee speed for 20 mil pitch parts?
>>Thanks all!
>>
>>Ryan Jennens
>>TelGen Corp.
>>
>>################################################################
>>TechNet E-Mail Forum provided as a free service by IPC using LISTSERV
1.8c
>>################################################################
>>To subscribe/unsubscribe, send a message to [log in to unmask] with
>>following text in the body:
>>To subscribe: SUBSCRIBE TechNet <your full name>
>>To unsubscribe: SIGNOFF TechNet
>>################################################################
>>Please visit IPC's web site (http://www.ipc.org) "On-Line Services"
>>section for additional information.
>>For technical support contact Hugo Scaramuzza at [log in to unmask] or
>>847-509-9700 ext.312
>>################################################################
>
>################################################################
>TechNet E-Mail Forum provided as a free service by IPC using LISTSERV
1.8c
>################################################################
>To subscribe/unsubscribe, send a message to [log in to unmask] with
following text
>n the body:
>To subscribe: SUBSCRIBE TechNet <your full name>
>To unsubscribe: SIGNOFF TechNet
>################################################################
>Please visit IPC's web site (http://www.ipc.org) "On-Line Services"
section for
>ditional information.
>For technical support contact Hugo Scaramuzza at [log in to unmask] or
847-509-9700
>t.312
>################################################################
>
>################################################################
>TechNet E-Mail Forum provided as a free service by IPC using LISTSERV
1.8c
>################################################################
>To subscribe/unsubscribe, send a message to [log in to unmask] with
following text in the body:
>To subscribe: SUBSCRIBE TechNet <your full name>
>To unsubscribe: SIGNOFF TechNet
>################################################################
>Please visit IPC's web site (http://www.ipc.org) "On-Line Services"
section for additional information.
>For technical support contact Hugo Scaramuzza at [log in to unmask] or
847-509-9700 ext.312
>################################################################
>
______________________________________________________
Get Your Private, Free Email at http://www.hotmail.com
################################################################
TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe: SUBSCRIBE TechNet <your full name>
To unsubscribe: SIGNOFF TechNet
################################################################
Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information.
For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312
################################################################
|