Subject: | |
From: | |
Reply To: | TechNet E-Mail Forum. |
Date: | Wed, 23 Dec 1998 10:53:53 -0600 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
The first thing I would try is to shorten the cure time to match Loctite's
tech. data sheet for 3609 ( 90-120sec. at 150C). I have been working with
our Loctite rep. trying to solve a hard to bond component issue. This was
their first suggestion. Your cure time at 4-5 min. will result in what
Loctite called a brittle cure. Shortening the time to the recommended range
of 90-120 seconds will result in a tougher and more flexible cure. Maybe
this will help, we've never had a problem bonding to any masks. We use 90sec
at 150C for both 3609 and 3614 for stencil printing.
I have just recieved a syringe of 3618, for hard to bond to materials,
which I'm told has been used at some of their customers to solve problems of
this type.
> ----------
> From: Wade Oberle[SMTP:[log in to unmask]]
> Reply To: TechNet E-Mail Forum.;Wade Oberle
> Sent: December 23, 1998 7:52 AM
> To: [log in to unmask]
> Subject: [TN] Surface Mount Adhesive
>
> Dear Technetters,
> I am having a problem with SMT adhesive sticking to some types
> of solder mask. Does someone out there have experience with using SMT
> adhesive on glossy boards vs. matte finish boards. I am using Loctite
> 3609 or Epibond 7275 or Epibond 7275-1 with a cure cycle of 145-150
> degrees centigrade for 4-5 minutes. Is there an SMT adhesive or cure
> cycle that works better with glossy boards? We seem to have a problem
> with adhesion at room temperature and at wave solder temperatures. We
> run a standard wave solder profile and have even increased the wave
> speed to 5.75 feet/minute from our norm of 4.5-5.0 feet/minute. This
> helps but we run the risk of voids and poor solder connections on some
> components.
> If I cure the boards and then use a 'push' tester to measure the force
> required to remove the 'glued' components, is there a standard for
> minimum and maximum expected force for removal? I have heard of some
> people using a custom socket and a torque wrench to measure the strength
> of the cured adhesive. Is there a standard specification for this test
> method? Which test method do you think is best? The tests mentioned
> above are done at room temperature. Is there a way to measure the 'hot'
> strength of the adhesive bond?
>
> Thanks in advance.
>
> Wade Oberle
>
> ################################################################
> TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
> ################################################################
> To subscribe/unsubscribe, send a message to [log in to unmask] with
> following text in the body:
> To subscribe: SUBSCRIBE TechNet <your full name>
> To unsubscribe: SIGNOFF TechNet
> ################################################################
> Please visit IPC's web site (http://www.ipc.org) "On-Line Services"
> section for additional information.
> For technical support contact Hugo Scaramuzza at [log in to unmask] or
> 847-509-9700 ext.312
> ################################################################
>
################################################################
TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe: SUBSCRIBE TechNet <your full name>
To unsubscribe: SIGNOFF TechNet
################################################################
Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information.
For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312
################################################################
|
|
|