TECHNET Archives

September 1998

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
Paul Wilson <[log in to unmask]>
Reply To:
TechNet E-Mail Forum.
Date:
Tue, 8 Sep 1998 06:20:07 -0400
Content-Type:
text/plain
Parts/Attachments:
text/plain (69 lines)
Obviously a nightmare ...

Ethylene glycol is soluble in water (of course), alcohol, ether, and acetone to various degrees.  One or a combination of these ought to work.

It is not understood what a "saponified solution"  means? [Generally, saponification refers to reaction of  lie and fat to generate soap].  If soap was added, it is likely insoluble in the ethylene glycol and precipitating as a white haze.  More water ought to remove this.

If one speaks of an alkaline solution, this could represent attack of the soldermask because that is how soldermask is stripped.  A solvent - solvent removal would probably be best eliminating detergents or soaps on the first pass --  I cannot say I ever had to do this, though, so good luck.

Paul Wilson
Manager of R&D / Plant Chemist
Circuit Center, Inc., 4738 Gateway Circle, Dayton, OH 45440
[log in to unmask]



----------
> Well, here's one for the books...  We have two in-circuit testers located next
> to each other.  Last week, during the night, an air-conditioning unit located
> in the ceiling directly above the testers sprung a leak, dumping a couple of
> gallons of ethylene glycol (heat transfer fluid) on the testers.  (It seems
> that the occasional condensation from the air-conditioner warranted a plastic
> sheet be placed under the unit, above the ceiling tiles.  So when the leak
> started, it collected in the plastic until the ceiling gave out!)
>
> Now, the questions:
>
> 1) The internal circuit boards plug into a mother board, so they can be
> removed
> easily.  Cleaning the boards in a saponified solution resulted in a white haze
> on the boards.  What might this be?
>
> 2) The boards were cleaned, but only half are working properly.  We expect
> some
> residue is left behind in some connectors.  What is the best way to clean
> these
> boards?
>
> 3) What is the long-term problem expected if residue is left behind?
>
> Thanks for your help,
> ICTless in NY
>
> ################################################################
> TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
> ################################################################
> To subscribe/unsubscribe, send a message to [log in to unmask] with following
> text in the body:
> To subscribe:   SUBSCRIBE TechNet <your full name>
> To unsubscribe:   SIGNOFF TechNet
> ################################################################
> Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section
> for additional information.
> For technical support contact Hugo Scaramuzza at [log in to unmask] or
> 847-509-9700 ext.312
> ################################################################
>

################################################################
TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe:   SUBSCRIBE TechNet <your full name>
To unsubscribe:   SIGNOFF TechNet 
################################################################
Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information.
For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312
################################################################


ATOM RSS1 RSS2