TECHNET Archives

August 1998

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
Reply To:
TechNet E-Mail Forum.
Date:
Wed, 26 Aug 1998 16:32:10 -0700
Content-Type:
text/plain
Parts/Attachments:
text/plain (89 lines)
Steve,

I have a son in Preschool who tried to attempt the same thing (putting a
square object into a round hole). After trying many times he finally
realized that only the round object will fit in the round hole.

Geez, don't you remember your early schooling days?

Brian

>Hi ya'll!
>
>I'm pretty sure that one or two of you "ol' crusty" types (I mean that in a
>GOOD way), have run across this problem I have a time or two. I have this
>board I'm building in a quasi "prototype/pre-production" run that has a PTH
>rectifier diode installed vertically...some of you have may have guessed what
>my problem is already from my subject, the hole's too small.
>Lead diameter is right around .050" +/- a mil or two, guess what the hole size
>is? .050", +/- a mil or two...that's just peachy ain't it? It goes two times
>per board, and we gotta' build a hundred of these, maybe two hundred.
>
>So tell me, what have all you "old salts" done to make a square peg to fit in
>a round hole? I've had some REALLY GOOD suggestions from some "experts" here,
>one was to get a dremel and drill the hole out (sounds good to me!...snicker),
>another was to get a can of "Freeze-it" and spray the diode leads with it,
>then hurry up and stuff it in the hole before it warms up and expands...that
>sounded pretty keen too, except it's hard to hold the diodes when you're
>wearing mittens to keep from getting your digits frostbitten.
>
>So I told my "helpers" that I really appreciated their suggestions, but that I
>would like to give the technet a chance to offer some guidance to me, and that
>no-way were the suggestions from the TechNet going to be as good as theirs,
>but I wanted to see what popped up...and I would come to them if I needed
>anymore "help"...in other words, don't call me, I'll call you.
>
>I'm sure glad this is email, it would be kinda' hard to carry on this
>conversation with my tongue in my cheek like this...
>
>So, what's the verdict? Am I hosed? I looked around on the NET trying to find
>the same spec'd diode with smaller lead diameters, but no joy. The only two
>companies I found were Motorola and General Instruments, and they both listed
>the same thing that I have now.
>
>Is there any trick that any of you have done to make something like this work?
>I'm afraid if I don't figure something out, I'll be in mittens spraying diodes
>with freeze-it on the production floor...ya' gotta save me!
>
>-Steve "soon to be numb-fingers" Gregory-
>
>################################################################
>TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
>################################################################
>To subscribe/unsubscribe, send a message to [log in to unmask] with following
text in the body:
>To subscribe:   SUBSCRIBE TechNet <your full name>
>To unsubscribe:   SIGNOFF TechNet
>################################################################
>Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section
for additional information.
>For technical support contact Hugo Scaramuzza at [log in to unmask] or
847-509-9700 ext.312
>################################################################
>
>
>



ETS, LLC - West                      ETS, Inc. - East
3939 N. Freya St.                    PO Box 47887
Spokane, WA 99207                    Plymouth, MN 55447
509-483-0900 (voice)                 612-553-0051 (voice)
509-483-0331 (fax)                   612-553-0246 (fax)
[log in to unmask]                        [log in to unmask]

Benefit from a direct relationship with the manufacturer!

################################################################
TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe:   SUBSCRIBE TechNet <your full name>
To unsubscribe:   SIGNOFF TechNet 
################################################################
Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information.
For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312
################################################################


ATOM RSS1 RSS2