The only way I know of doing this is to cut and paste the properties
from the properties report and creating a properties.net file.
Or you can write a script to do this for you.  You can then read this
in, third party, with supersedes turned off.  See example below:

$NETS
$A_PROPERTIES
DELAY_RULE P3401.82:U3401.AB2:3000.00:4000.00:U3401.AB2:U3403.B23:4000.00:7000.00; LB0_BDVLD_L
DELAY_RULE J3401.83:U3401.AA3:3000.00:4000.00:U3401.AA3:U3403.B24:4000.00:7000.00; LB0_BTAG_0
DELAY_RULE J3401.85:U3401.AA2:3000.00:4000.00:U3401.AA2:U3403.G24:4000.00:7000.00; LB0_BTAG_1
DELAY_RULE J3401.27:U3401.AD1:3000.00:4000.00:U3401.AD1:U3403.G2:4000.00:7000.00; LB0_DAT_0
DELAY_RULE J3401.28:U3401.AD2:3000.00:4000.00:U3401.AD2:U3403.J2:4000.00:7000.00; LB0_DAT_1
DELAY_RULE P3401.28:U3401.AF2:3000.00:4000.00:U3401.AF2:U3403.E2:4000.00:7000.00; LB0_DAT_2
DELAY_RULE P3401.27:U3401.AE2:3000.00:4000.00:U3401.AE2:U3403.C2:4000.00:7000.00; LB0_DAT_3
$END


Good Luck,
Gemma


Danna, Paul wrote:

> I have a design that was restored from a .SAV file. I have been able to
> reconstruct this design up to the point of retaining the properties
> associated with the Nets. I can extract a list of these properties with
> report option npr (Properties on Nets); however, I can not read this
> information into the reconstructed design.
>
> Is there away to do this without manually entering the properties or writing
> a script to append a Property section at the end of the netlist from the npr
> report?
>
> Thanks in advance.
>
> Paul Danna
> [log in to unmask]
>
> Paul Danna
> PCB Design                        Compaq Computer Corp.
> Phone (281) 518-6735        PO Box 692000
> Fax (281) 518-6122              MS080403
> [log in to unmask]   Houston, Texas 77269-2000
>
> ################################################################
> DesignerCouncil E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
> ################################################################
> To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
> To subscribe:   SUBSCRIBE DesignerCouncil <your full name>
> To unsubscribe:   SIGNOFF DesignerCouncil
> ################################################################
> Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information.
> For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312
> ################################################################



--

***************************************************
Gemma Gylling   CAD Application Engineer
Cisco Systems, Inc. Mailstop SJ-H/1/3
170 West Tasman Drive, San Jose, CA 95134-1706
Phone: 408-527-2987   FAX:  408-527-6321
email:  [log in to unmask] epage:  [log in to unmask]
pager: 800-796-7363 pin 102-8664
***************************************************

################################################################
DesignerCouncil E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe:   SUBSCRIBE DesignerCouncil <your full name>
To unsubscribe:   SIGNOFF DesignerCouncil 
################################################################
Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information.
For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312
################################################################