While we do not do assembly here (do precision images on film/glass), your
statement of "Balance Air Ionizer" has my attention. Could you explain
or steer me to some literature?
Thanks
Alex
----------
> From: Gagrani, Kishore <[log in to unmask]>
> To: [log in to unmask]
> Subject: Re: [TN] ESD buildup on SMT reels
> Date: Monday, May 04, 1998 2:21 PM
>
> Yes , while an air ionizer looks OK , but you need be very cautious
> using the same , use of "Balance Air Ionizer" would be better option
> (but only after a good analysis of situation).
>
> Thanks
>
>
> -----Original Message-----
> From: Charles Barker [mailto:[log in to unmask]]
> Sent: Monday, May 04, 1998 2:40 PM
> To: [log in to unmask]
> Subject: Re: [TN] ESD buildup on SMT reels
>
> Charles Barker@I-O INC
> 05/04/98 01:39 PM
>
> Neil,
> An air ionizer at the machine might take care of your problem.
>
>
>
>
> Please respond to [log in to unmask]; Please respond to
> [log in to unmask]
>
> To: [log in to unmask]
> cc: (bcc: Charles Barker/US/I-O INC)
> Subject: [TN] ESD buildup on SMT reels
>
>
>
>
> Greetings Technet!
> I've got a problem.
> My operator just put a new 7"reel of type 1210-07 1.5K 1/2W
> resistors
> (QTY 4000) on our Mydata PNP machine, only to find that most of the
> components are sticking to the cover sheet as it is being pulled back
> from
> the tape. Upon investigation, I discovered nothing adhesive or
> "sticky" on
> the cover sheet, but the whole reel registers 500 - 3Kv on the ESD
> meter.
> The reel itself is of a typical blue plastic "ESD safe" variety
> just
> like the dozen others on the machine that read "0" on the meter. So it
> must
> be the tape, which is made of "clear" plastic.
> My question is .... is the tape itself made of an inferior grade
> of
> plastic, or was the reel subjected to a massive static charge? My
> entire
> facility, including the bathrooms, is ESD safe. Our inventory is
> stored in
> ESD safe bins. Everybody wears ESD straps here, besides, I don't think
> Dr.
> Tesla himself could generate enough static on his person to zap this
> reel,
> without blowing a finger off.
> The supplier has not returned our phone calls. (Imagine my
> surprise.)
> Seriously, I am worried that something got in here that is our of
> our
> control.
> Has anybody else had this problem?
> Did the supplier use bad plastic?
> Is the reel of parts finished?
> Can I dissipate this charge, or will it build up again when the reel
> is
> back on the machine?
> Do vendors ever answer their phones?
> Thank you in advance for your replies.
>
>
> Neil Maloney, Service Technician
> Contemporary Control Systems,Inc
> 2512 Wisconsin Ave. Downers Grove, IL.60515 USA
> (630) 963-7070 x132
> E-mail: [log in to unmask]
> URL: http://www.ccontrol.com
>
> ################################################################
> TechNet E-Mail Forum provided as a free service by IPC using LISTSERV
> 1.8c
> ################################################################
> To subscribe/unsubscribe, send a message to [log in to unmask] with
> following text in the body:
> To subscribe: SUBSCRIBE TechNet <your full name>
> To unsubscribe: SIGNOFF TechNet
> ################################################################
> Please visit IPC web site (http://jefry.ipc.org/forum.htm) for
> additional information.
> For the technical support contact Dmitriy Sklyar at [log in to unmask] or
> 847-509-9700 ext.311
> ################################################################
>
> ################################################################
> TechNet E-Mail Forum provided as a free service by IPC using LISTSERV
1.8c
> ################################################################
> To subscribe/unsubscribe, send a message to [log in to unmask] with
following text in the body:
> To subscribe: SUBSCRIBE TechNet <your full name>
> To unsubscribe: SIGNOFF TechNet
> ################################################################
> Please visit IPC web site (http://jefry.ipc.org/forum.htm) for additional
information.
> For the technical support contact Dmitriy Sklyar at [log in to unmask] or
847-509-9700 ext.311
> ################################################################
>
################################################################
TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe: SUBSCRIBE TechNet <your full name>
To unsubscribe: SIGNOFF TechNet
################################################################
Please visit IPC web site (http://jefry.ipc.org/forum.htm) for additional information.
For the technical support contact Dmitriy Sklyar at [log in to unmask] or 847-509-9700 ext.311
################################################################
|