I have had a good experience working on floor for ESD. Normally the
conductivity of the floor is within the range for initial couple of
years (my floor was OK for 5 years) even with normal vax (I would
recommend periodic testing though, as per EOS/ESD Stds.) , after that
you may want to start applying special ESD VAX, I evaluated two vaxes
from different companies and one of them gave me good result .
You might want to hear about these VAX companied off line from me,
please drop me a mail .
Thanks
Kishore Gagrani
[log in to unmask]
-----Original Message-----
From: Cash, Alan [mailto:[log in to unmask]]
Sent: Thursday, April 30, 1998 7:41 PM
To: [log in to unmask]
Subject: Re: [TN] GEN:Conductive Floor Tile Care
Conductive floors must not be waxed with ordinary wax. The
manufacturer of
the conductive floor should provide you with maintenance instructions.
You
may wish to have a shiny finish on the floors. It does impress the
customers and visitors. There are many good static dissipative
finishes
which are reasonable in price now available. Some new types are
identified
as long life floor finishes. The material costs are a little higher
than
industrial floor waxes, but the maintenance of the floor is about the
same.
Call me and I will give you some waxes that I know are good. Set uo a
test
area and test several waxes to find the one that gives you the gloss
that
you want and the life that you need, with the minimum of maintance.
Al Cash
Northrop Grumman ESID-ES
847-259-9600
> ----------
> From: SteveZeva[SMTP:[log in to unmask]]
> Reply To: TechNet E-Mail Forum.;SteveZeva
> Sent: Tuesday, April 28, 1998 11:03 AM
> To: [log in to unmask]
> Subject: [TN] GEN:Conductive Floor Tile Care
>
> Good Day All!
>
> I've just joined a start-up company, and really we had a stroke
of
> luck
> with the building we're moving into. Not only do I have most of the
power,
> compressed air lines, and exhaust ducting I need for the equipment
already
> routed and installed out on the production floor, but we also have
> conductive
> tile on the floor too! (...and that stuff not be cheap!)
>
> We're going to be a contract assembly company, I know that it
always
> makes a good impression with potential customers to walk on to a
> manufacturing
> floor that is clean and shiny, and that's my problem...
>
> I searched the technet archives about esd floor care and
conductive
> waxes, and there were a lot of negative comments when it came to
esd
> waxes...many said they weren't dependable and could even cause
> problems...not
> to mention the cost, it's well over $25.00 a gallon and we've got a
good
> 10-12,000 square foot manufacturing floor...
>
> ...Does anybody know of any good waxes?
> ...Any that don't cost an arm and a leg?
> ...Should I even wax the floor?
>
> I appreciate any comments!
>
> -Steve Gregory-
>
> ################################################################
> TechNet E-Mail Forum provided as a free service by IPC using
LISTSERV 1.8c
> ################################################################
> To subscribe/unsubscribe, send a message to [log in to unmask] with
> following text in the body:
> To subscribe: SUBSCRIBE TechNet <your full name>
> To unsubscribe: SIGNOFF TechNet
> ################################################################
> Please visit IPC web site (http://jefry.ipc.org/forum.htm) for
additional
> information.
> For the technical support contact Dmitriy Sklyar at [log in to unmask]
or
> 847-509-9700 ext.311
> ################################################################
>
################################################################
TechNet E-Mail Forum provided as a free service by IPC using LISTSERV
1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with
following text in the body:
To subscribe: SUBSCRIBE TechNet <your full name>
To unsubscribe: SIGNOFF TechNet
################################################################
Please visit IPC web site (http://jefry.ipc.org/forum.htm) for
additional information.
For the technical support contact Dmitriy Sklyar at [log in to unmask] or
847-509-9700 ext.311
################################################################
################################################################
TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe: SUBSCRIBE TechNet <your full name>
To unsubscribe: SIGNOFF TechNet
################################################################
Please visit IPC web site (http://jefry.ipc.org/forum.htm) for additional information.
For the technical support contact Dmitriy Sklyar at [log in to unmask] or 847-509-9700 ext.311
################################################################
|
