TECHNET Archives

May 1998

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
Michael Carano <[log in to unmask]>
Reply To:
TechNet E-Mail Forum.
Date:
Fri, 8 May 1998 17:55:30 -0700
Content-Type:
text/plain
Parts/Attachments:
text/plain (72 lines)
John Waite wrote:
>
> Hi Bill,
>     A solderball is basically a "glob" of solder that is either stuck to the surface or
> entrenched in a material where it should not be (sorry, as generic as I can put it).  There are
> different types of solderballs (depending on how and where they are stuck) and caused by
> different issues.  Some examples and causes are:  1) solderball stuck on the surface of the
> soldermask- Many causes including, flux density or preheat too high, undercured soldermask
> (typically more entrenched).  soldermask tooooo Thinnnnn.   Poor postclean.  2) solderball stuck
> on the edge of a mask clearance- Exposed circuit from excessive undercut, cleaning, mask curing,
> etc, etc.  Instead of boring you with all the history,  It is possible that a poorly aligned
> solderpaste stencil can cause a solderball, but Look at the placement of the solderball, Webbing
> characteristics between the SMT pads, and cross section the area to find out where it is attached
> to.  This may give you a clue as to the cause.  Sounds like they may also be depositing a heavy
> amount of paste and possibly using a noclean environment? There are other causes on SMT
> technology also to include the profile of the smt reflow unit, solderpaste itself, cleanliness of
> the board, etc.  I am not an assembly guru (far from it), but have seen some "interesting"
> solderballs.  (No jokes please, I was being good about it).  JOHN WAITE
>
> [log in to unmask] wrote:
>
> > Hi all I have what I am sure amounts to a dumb question but I have to
> > know.I have a customer that I talked to and they told me that they
> > thought that the stencil step was off from the panel step and it was
> > causing solder balls.I have read in the past on this site a little about
> > solder balls but paid no mind to them (silly me) but now I have to.
> >  My question is what is a solder ball? And does or can an off step cause
> > them.
> >
> > Thank you Bill Dworak
> >
> > ################################################################
> > TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
> > ################################################################
> > To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
> > To subscribe:   SUBSCRIBE TechNet <your full name>
> > To unsubscribe:   SIGNOFF TechNet
> > ################################################################
> > Please visit IPC web site (http://jefry.ipc.org/forum.htm) for additional information.
> > For the technical support contact Dmitriy Sklyar at [log in to unmask] or 847-509-9700 ext.311
> > ################################################################
>
> ################################################################
> TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
> ################################################################
> To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
> To subscribe:   SUBSCRIBE TechNet <your full name>
> To unsubscribe:   SIGNOFF TechNet
> ################################################################
> Please visit IPC web site (http://jefry.ipc.org/forum.htm) for additional information.
> For the technical support contact Dmitriy Sklyar at [log in to unmask] or 847-509-9700 ext.311
> ################################################################Bill,
One area to look at is the soldermask itself. Is it properly cured?
Try a littke longer on the post cure or extend the UV bump.
Also, some masks are more prone to solderballs than others.
John Waite covered many of the other causes very well. Yes, it is a lot
of things to look at.

Good luck

################################################################
TechNet E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe:   SUBSCRIBE TechNet <your full name>
To unsubscribe:   SIGNOFF TechNet 
################################################################
Please visit IPC web site (http://jefry.ipc.org/forum.htm) for additional information.
For the technical support contact Dmitriy Sklyar at [log in to unmask] or 847-509-9700 ext.311
################################################################


ATOM RSS1 RSS2