Sender: |
|
X-To: |
|
Date: |
Mon, 19 Jan 1998 07:17:39 -0700 |
Reply-To: |
|
Subject: |
|
MIME-Version: |
1.0 |
Content-Transfer-Encoding: |
7bit |
Content-Type: |
text/plain; charset=ISO-8859-1 |
From: |
|
Parts/Attachments: |
|
|
One Kyu Son would it be possible to get an example of the L-Cut you are
talking about? I am putting a paper together for the upcoming IPC
conference it this would be good inf. to be incorporated.
Thanks.
Steve Collins
Antec Corporation
----------
> From: CSS International Corp. <[log in to unmask]>
> To: [log in to unmask]
> Subject: Re: [TN] BURR
> Date: Friday, January 16, 1998 1:53 PM
>
> There are many ways you can try to control this process.
>
> First is to change the design to do more routing in the critical
dimension
> areas and then use the scoring (either L-Cut or V-Cut).
>
> Second is to use L-Cut (instead of V-Cut) as this will give you better
> control on your burr dimension. And have a tight tolerance for the upper
> and lower side offset. And minimized the web thickness as much as
possible
> without breaking them during component mounting.
>
> Third, you can use a side grinding machine to automatically sand the
edges
> if you do not have a dust problem. We have a unit we built by ourselves
> which works very nicely.
>
> The dimension changes due to burr will depend on each type of board (due
to
> glass size and structure) you are talking about as well as how you
> depanelize the boards. We did an extensive study with our customer about
> five years ago. To get the exact record it will take too much time.
>
> We hope this helps a little.
>
>
> Best Regards,
> One Kyu Son
>
>
>
> At 05:39 PM 1/16/98 +0000, you wrote:
> > Good day Folks,
> >
> > We face dimension problem after depanellise the v-scoring board.
The
> > board's thickness is 0.062" and the v-scoring remaining thickness
is
> > 0.015". After depanellise, the board dimension is found to increase
by
> > 0.01".
> >
> > According to the fab. house, this is caused by the burr
(protrusion)
> > after depanelling the board.
> >
> > Is there any standard spec. for the burr after depanelling the
> > v-scoring board? What is the general dimension tolerance used in
> > design the board with v-scoring?
> >
> >
> > Thanks
> >
> >
> > Robert
> >
> >##############################################################
> >TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
> >##############################################################
> >To subscribe/unsubscribe, send a message to [log in to unmask] with
following
> text in the body:
> >To subscribe: SUBSCRIBE TECHNET <your full name>
> >To unsubscribe: SIGNOFF TECHNET
> >##############################################################
> >Please visit IPC web site (http://www.ipc.org/html/forum.htm) for
> additional information.
> >For the technical support contact Dmitriy Sklyar at [log in to unmask] or
> 847-509-9700 ext.311
> >##############################################################
> >
>
>
> CSS International Corp.
> 460 Bergen Boulevard, Suite 209
> Palisades Park, NJ 07650 U.S.A.
> Tel: 1-201-461-7205
> Fax: 1-201-461-6374
> E-Mail: [log in to unmask]
>
> ##############################################################
> TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
> ##############################################################
> To subscribe/unsubscribe, send a message to [log in to unmask] with
following text in the body:
> To subscribe: SUBSCRIBE TECHNET <your full name>
> To unsubscribe: SIGNOFF TECHNET
> ##############################################################
> Please visit IPC web site (http://www.ipc.org/html/forum.htm) for
additional information.
> For the technical support contact Dmitriy Sklyar at [log in to unmask] or
847-509-9700 ext.311
> ##############################################################
##############################################################
TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
##############################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe: SUBSCRIBE TECHNET <your full name>
To unsubscribe: SIGNOFF TECHNET
##############################################################
Please visit IPC web site (http://www.ipc.org/html/forum.htm) for additional information.
For the technical support contact Dmitriy Sklyar at [log in to unmask] or 847-509-9700 ext.311
##############################################################
|
|
|