I was told that use of OSP keeps ICT probes from penetrating the coating
to have a reliable contect for PCMCIA cards, which means OSP is not
suitable for PCMCIA cards. Is it true? Is Ni-Au the only option then for
flat pads?
Thanks,
Yuan
On Fri, 5 Dec 1997 [log in to unmask] wrote:
> Matthew:
>
> From my perspective, the question that needs to be addressed FIRST is
> where in the process is the ENTEK applied to the board.
>
> 1) ENTEK BEFORE or AFTER Bare Board Test
>
> By itself, ENTEK is an insulator. Therefore, if it is applied PRIOR
> to bare board testing, the bare board test probes can create "false
> opens" due to residue buildup on the tips of the probes. This
> might indicate that ENTEK AFTER bare board test would be better.
>
> On the other hand, a mild microetch is used to prepare the surface
> prior to ENTEK application. If the dip process is used and the
> microetch is fresh (i.e. strong solution), excessive etching can
> result. This can result in circumferential barrel voids at the
> knee of the holes, where the copper is the thinnest. If ENTEK is
> applied AFTER TEST, this type of defect will not be discovered
> until the board has been populated with expensive components.
>
> Some people subscribe to the policy "NO chemical operation shall be
> performed AFTER bare board testing". Each vendor's process and
> controls must be evaluated to assess the likelihood for this type
> of failure.
>
> 2) In-line vs. Batch
>
> In my opinion, in-line would be better and more repeatable, if the
> total volume of boards that the vendor processes warrant the
> equipment expense. Properly managed, the dip process will work.
>
> 3) "Spotted" Boards:
>
> Another "problem" to look out for is moisture spotting during
> shipment. ENTEK uses a DI rinse in the process and, if vias are
> small (0.013" dia.), moisture can be trapped inside the barrel of
> those vias. Placing the "drip-dried" board in a plastic bag for
> shipment, can result in residual moisture STILL residing in the
> bag. Shipment of the boards to the final destination (shipping
> vibration, change in temperature, etc.) causes the moisture to
> migrate to the inside surface of the bag and, in turn, back onto
> the board. The thickness of the ENTEK on the board will be reduced
> where there is intimate moisture contact. The appearance looks like
> "water spots" on a drinking glass. They COULD result in localized
> ENTEK "voids" and potentially cause solderability problems, if the
> boards are left on the shelf for an extended period of time.
>
> One test for "dryness" of a board is a deceptably simple one:
>
> a) Take a piece of colored construction paper (or the cardboard
> stiffener on the back of a pad of paper) that will darken when
> exposed to water and place it on a flat surface (e.g. table).
>
> b) Take a "dry" board and firmly slap the face of the board onto
> the cardboard. If it shows dark spots on the cardboard when the
> fab is removed, the fab is NOT dry and could caule spotting
> during shipment.
>
> My suggestion is to have the boards BAKED after ENTEK to eliminate
> this potential problem.
>
> I advocate the use of ENTEK for fine pitch QFP designs, because of the
> resultant pad flatness, as compared with HASL. However, it does have
> some "side effects" to watch out for. It is NOT the "panacea for all
> ills", but it is better than some of the alternatives in certain
> designs.
>
> The above opinions are my own, etc.,etc., etc.
>
> Good Luck!
>
> Bill Fabry
> Plantronics, Inc.
> (408) 458-7555
>
> e-mail: [log in to unmask]
>
>
> ______________________________ Reply Separator _________________________________
> Subject: [TN] entek plus process
> Author: "TechNet Mail Forum." <[log in to unmask]> at INTERNET
> Date: 12/5/97 9:58 AM
>
>
> I am getting confusing responses from a board vendor that
> uses in-line process, and from a board vendor that uses
> dipping process to coat boards with Entek Plus.
>
> What are advantage/disavantage using either process?
>
> What are problem associated with boards that were
> fabricated using dipping process?
>
> Does in-line processing provide better consistent and
> controllable coating (typ: 0.35um) than dipping process?
>
> Is there any other coating thickness measurement technique
> used by board vendors other than the sampling method
> specified by Enthone using UV spectrophotometer?
>
> What are some of inspection method employed by board
> vendors to check boards are coompletely dry prior packaging
> and shipping?
>
> advance thanks
> regards
> Matthew
>
> ##############################################################
> TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
> ##############################################################
> To subscribe/unsubscribe, send a message to [log in to unmask] with following text
> in the body:
> To subscribe: SUBSCRIBE TECHNET <your full name>
> To unsubscribe: SIGNOFF TECHNET
> ##############################################################
> Please visit IPC web site (http://www.ipc.org/html/forum.htm) for additional
> information.
> For the technical support contact Dmitriy Sklyar at [log in to unmask] or
> 847-509-9700 ext.311
> ##############################################################
>
> ##############################################################
> TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
> ##############################################################
> To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
> To subscribe: SUBSCRIBE TECHNET <your full name>
> To unsubscribe: SIGNOFF TECHNET
> ##############################################################
> Please visit IPC web site (http://www.ipc.org/html/forum.htm) for additional information.
> For the technical support contact Dmitriy Sklyar at [log in to unmask] or 847-509-9700 ext.311
> ##############################################################
>
##############################################################
TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
##############################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe: SUBSCRIBE TECHNET <your full name>
To unsubscribe: SIGNOFF TECHNET
##############################################################
Please visit IPC web site (http://www.ipc.org/html/forum.htm) for additional information.
For the technical support contact Dmitriy Sklyar at [log in to unmask] or 847-509-9700 ext.311
##############################################################
|