Subject: | |
From: | |
Reply To: | DesignerCouncil Mail Forum. |
Date: | Fri, 21 Nov 1997 11:40:42 -0600 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
JoAnn,
Can you set your artwork format to 2.4 instead of 2.3
before you generate your artwork? This is what I've done in
my software packages (Cadence & Mentor).
Karl
EXAMPLE follows......
ARTWORK FORMAT
Photoplotter coordinate mode is absolute
Photoplotter does not support circular interpolation
Arcs and circles are interpolated by 32 segments
Photoplotter supports Gerber G code
Photoplotter supports inch units
Scale is 1.000
Data format 2.3 <<<<<<< THIS IS WHERE YOU WOULD CHANGE to 2.4 IN YOUR SOFTWARE
Photoplotter modal coordinate is off
Photoplotter modal shutter open(D01) is off
Leading zeros are present
Trailing zeros are present
Record length of the artwork output file is 80
Film size is(width by height) : 16.000000 by 20.000000
Automatic offset specified will center board artwork on film sheet
Distance from film(0,0) to board origin is(x,y): 4.000000 , 4.000000
Panel artwork offset is(0 ,0).
Photoplotter command block end char is '*'
Photoplotter machine stop code is 'M02'
> From [log in to unmask] Thu Nov 20 14:24 CST 1997
> To: [log in to unmask]
> MIME-Version: 1.0
> Content-transfer-encoding: 7BIT
> Date: Thu, 20 Nov 1997 14:35:14 +0000
> Comments: Authenticated sender is <[log in to unmask]>
> From: JoAnn Amerson <[log in to unmask]>
> Subject: [DC] Gerber format
> Original-To: [log in to unmask]
>
> Okay folks. I need to earn some brownie points. How can we output RS-274X
> Gerber files that hold a FOUR place decimal? We still work with English units
> and are just starting to get into fine pitch components (.50mm). We can't
> output that accurately. We are currently using Cadstar V2.3 for our design
> layout and ECAM to view the files prior to sending them off.
>
> Any and all help would be GREATLY appreciated.
>
>
> JoAnn L. Amerson
> Design Librarian
> Red Lion Controls, Inc.
> E-mail: [log in to unmask]
> Voice: (717) 767-6961 ext 6308
>
> ##############################################################
> IPC Designers Council Mail List provided as a free service by IPC using
LISTSERV 1.8c
> ##############################################################
> To subscribe/unsubscribe, send a message to [log in to unmask] with following
text in the body:
> To subscribe: SUBSCRIBE DESIGNERCOUNCIL <your full name>
> To unsubscribe: SIGNOFF DESIGNERCOUNCIL
> ##############################################################
> Please visit IPC web site (http://www.ipc.org/html/forum.htm) for additional
information.
> For the technical support contact Dmitriy Sklyar at [log in to unmask] or
847-509-9700 ext.311
> ##############################################################
>
##############################################################
IPC Designers Council Mail List provided as a free service by IPC using LISTSERV 1.8c
##############################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe: SUBSCRIBE DESIGNERCOUNCIL <your full name>
To unsubscribe: SIGNOFF DESIGNERCOUNCIL
##############################################################
Please visit IPC web site (http://www.ipc.org/html/forum.htm) for additional information.
For the technical support contact Dmitriy Sklyar at [log in to unmask] or 847-509-9700 ext.311
##############################################################
|
|
|