Content-Transfer-Encoding: |
7bit |
Sender: |
|
Subject: |
|
From: |
|
Date: |
Thu, 23 Oct 1997 13:28:47 -0400 |
Content-Type: |
text/plain; charset="us-ascii" |
MIME-Version: |
1.0 |
Reply-To: |
|
Parts/Attachments: |
|
|
Dave, Sheila,
Although soldering irons can certainly melt the 95/5 solder isn't there
an increased risk of damage to the board because of the application of
the higher temperature to the FR-4?
Bev Christian
Nortel
[log in to unmask]
>----------
>From: David D Hillman[SMTP:[log in to unmask]]
>Sent: Thursday, October 23, 1997 11:59 AM
>To: [log in to unmask]
>Subject: Re: [TN] [TECHNET] ASSY: Solder compatibility
>
>Hi Sheila - a question - do you know that the voids are detrimental to
>solder joint reliability? Also mixing of 95/5 with Sn62 is probably not
>going to give you an intermetallic issue but you will probably get a
>reeeaallly neat solder joint composition which will be very hard to predict
>any type of properities data or even a simple melting point. If you must do
>touchup why not use 95/5 as the touchup alloy? Soldering irons can melt
>that alloy. Good Luck.
>
>Dave Hillman
>Rockwell Collins
>[log in to unmask]
>
>
>
>
>
>[log in to unmask] on 10/21/97 10:05:36 AM
>
>Please respond to [log in to unmask]; Please respond to [log in to unmask]
>
>To: [log in to unmask]
>cc: (bcc: David D Hillman/CedarRapids/Collins/Rockwell)
>Subject: [TECHNET] ASSY: Solder compatibility
>
>
>
>
>Hello TechNet ..
>Does anyone have any experience with possible intermetallics formation if I
>use Sn62Pb362Ag to touchup voids in a Vapor phase reflowed Sn95Sb5 solder
>joint ??? Especially after 100 temp cycles from -55C to 120C? Thanks for
>any help!
>Sheila Smith, Tracor AES
>##############################################################
>TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
>##############################################################
>To subscribe/unsubscribe, send a message to [log in to unmask] with following
>text in the body:
>To subscribe: SUBSCRIBE TECHNET <your full name>
>To unsubscribe: SIGNOFF TECHNET
>##############################################################
>Please visit IPC web site (http://www.ipc.org/html/forum.htm) for
>additional information.
>For the technical support contact Dmitriy Sklyar at [log in to unmask] or
>847-509-9700 ext.311
>##############################################################
>
>##############################################################
>TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
>##############################################################
>To subscribe/unsubscribe, send a message to [log in to unmask] with following
>text in the body:
>To subscribe: SUBSCRIBE TECHNET <your full name>
>To unsubscribe: SIGNOFF TECHNET
>##############################################################
>Please visit IPC web site (http://www.ipc.org/html/forum.htm) for additional
>information.
>For the technical support contact Dmitriy Sklyar at [log in to unmask] or
>847-509-9700 ext.311
>##############################################################
>
##############################################################
TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
##############################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe: SUBSCRIBE TECHNET <your full name>
To unsubscribe: SIGNOFF TECHNET
##############################################################
Please visit IPC web site (http://www.ipc.org/html/forum.htm) for additional information.
For the technical support contact Dmitriy Sklyar at [log in to unmask] or 847-509-9700 ext.311
##############################################################
|
|
|