Patrick Ducas wrote:
>
> Tom, just a easy one, what type of tool do you use to measure the thickness
> of solder? Is it accurate for that specific application? If you know some
> tools that should be enough accurate, any hint would be appreciated.
>
> Thanks in advance
>
> >
> > Don:
> > The thickness of solder from a solder level operation
> > is dependent upon pad geometry, amongst other things. Board
> > fabbers walk the tightrope between blowing enough solder out
> > of the holes yet leaving enough remaining on the surface
> > mount pads.
> > I would strongly urge you to specify a horizontal HASL
> > process from your board vendors. Boards should also be
> > cocked at a 45 degree angle when going into the solder to
> > offset a "north-south, east-west" bias on QFPS.
> > Getting back to the pad geometry, the larger the pad,
> > the thinner the solder coat is apt to be, because the solder
> > has a larger surface over which to retreat. Worst case
> > would probably be discrete pads, where we have a stated
> > minimum of 50 microinches at the pad center. Maximum solder
> > thickness can be held to .0015".
> > Where the solder is measured is another issue. We
> > always ask our customers to measure from the pad centroid so
> > that outgoing and incoming measurements are apples and
> > apples. The pad center may or may not be the crest, and it
> > usually isn't. When I see thicknesses called out in specs
> > that say "as measured at the crest", I chuckle because it
> > would take too long just to find the crest of a given pad.
> > In all cases, your board fabricator should guarantee
> > solderability.
> > In summary, the most workable callout would be a solder
> > thickness of .0001" nominal, .00005" minimum, .0015" maximum
> > (all measurements taken at pad center). Again,
> > solderability is to be guaranteed.
> > Regards,
> > Tom Coyle
> > Field Services Engineer
> > HADCO Corporation
> >
> >***************************************************************************
> >* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
> >***************************************************************************
> >* To subscribe/unsubscribe send a message <to: [log in to unmask]> *
> >* with <subject: subscribe/unsubscribe> and no text in the body. *
> >***************************************************************************
> >* If you are having a problem with the IPC TechNet forum please contact *
> >* Dmitriy Sklyar at 847-509-9700 ext. 311 or email at [log in to unmask] *
> >***************************************************************************
> >
> >
> >
> -------------------------------------------------
> Patrick Ducas
> Process Quality Engineer
> Matrox Electronic Systems Ltd
> E-mail: [log in to unmask]
> Tél:(514)969-6000 ext.2971 Fax:(514)685-3415
> -------------------------------------------------
>
>
> ***************************************************************************
> * TechNet mail list is provided as a service by IPC using SmartList v3.05 *
> ***************************************************************************
> * To subscribe/unsubscribe send a message <to: [log in to unmask]> *
> * with <subject: subscribe/unsubscribe> and no text in the body. *
> ***************************************************************************
> * If you are having a problem with the IPC TechNet forum please contact *
> * Dmitriy Sklyar at 847-509-9700 ext. 311 or email at [log in to unmask] *
> ***************************************************************************
Hi,TechNetters,
Patrick asked Tom how he measures the solder thickness on SMT pads.
I measure the thickness with X-Ray,which gives me the following
opportunities:
1:I can perform several measurements on the same pad.
2:I see WHERE I measure,and usually I find the crest-don't ask me how
much time it takes.
3:I can determine also the composition of the solder.
Tom's suggestion about 45 degrees is very correct, I think, I have seen
differences of 40 micrometers or more between N-S and E-W.
Here my experience ends,and because there is always Dave,I will also ask
one question:
Why do I get different Tin content levels on the same board,depending on
the solder thickness I found?
In the range of ~1micrometer I get higher readings,although the alloy is
"recognizable".
Is it a calibration error, the real thing, or me?
Bye
Gaby
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To subscribe/unsubscribe send a message <to: [log in to unmask]> *
* with <subject: subscribe/unsubscribe> and no text in the body. *
***************************************************************************
* If you are having a problem with the IPC TechNet forum please contact *
* Dmitriy Sklyar at 847-509-9700 ext. 311 or email at [log in to unmask] *
***************************************************************************
|