Subject: | |
From: | |
Date: | 30 May 97 09:29:26 EDT |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Sender: [log in to unmask]
Received: from kani.wwa.com (kani.wwa.com [198.49.174.58]) by arl-img-4.compuserv
e.com (8.6.10/5.950515)
id RAA07328; Thu, 29 May 1997 17:03:17 -0400
Resent-Date: Thu, 29 May 1997 17:03:17 -0400
Received: from ipc.org/ipc.ipc.org [209.42.29.23] by kani.wwa.com with smtp
(Smail3.2.WWA) id m0wXCKs-003peUC; Thu, 29 May 1997 16:02:34 -0500 (CDT)
Received: by ipc.org (Smail3.1.28.1 #2)
id m0wXCBI-000BjPC; Thu, 29 May 97 15:52 CDT
Resent-Sender: [log in to unmask]
Old-Return-Path: <[log in to unmask]>
Message-Id: <1.5.4.32.19970529210129.0068e16c@glitch>
X-Sender: alaberge@glitch
X-Mailer: Windows Eudora Light Version 1.5.4 (32)
Mime-Version: 1.0
Content-Type: text/plain; charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
Date: Thu, 29 May 1997 17:01:29 -0400
To: [log in to unmask]
From: annie laberge <[log in to unmask]>
Subject: Re: Re[2]: LPISM Stripping
Resent-Message-ID: <"KfoSj1.0.jM7.ynUZp"@ipc>
Resent-From: [log in to unmask]
X-Mailing-List: <[log in to unmask]> archive/latest/13022
X-Loop: [log in to unmask]
Precedence: list
Resent-Sender: [log in to unmask]
============== Begin part 2 ==========================
Annie,
I have found that heating the solder mask with a hot air soldering
tool will soften the epoxy. It can than be easily scraped off with a
dull (less change of etch damage) Xacto knife. Be careful not to
concentrate the air on one spot for too long.
Gary Camac
Dickey-john Corp.
[log in to unmask]
______________________________ Reply Separator _________________________________
Subject: Re: Re[2]: LPISM Stripping
Author: INTERNET:[log in to unmask] at CSERVE
Date: 5/29/97 5:03 PM
Regarding soldermask stripping...
We are an assembly plant and sometimes we want to remove soldermask (PISM)
on PCB but just on a small area.
I was wondering if there is anything that we can use to remove soldermask
other than physically remove it with "x-acto" (considering you just want
to strip a little area on the board; not the entire board.
Thanks in advance
Annie Laberge
Quality Engineer
Matrox Electronic Systems
At 07:12 PM 5/28/97 -0500, you wrote:
> Vince,
>
> Is this before or after cure? I've had some bad experience with
> stripping soldermask after being cured, especially batched stripped
> versus in-line spray method. Worse case scenario, conductors lifting
> from laminate, expecially in isolated areas. This was two years ago,
> so what has changed? I currently have a situation with a vendor where
> the soldermask is very thick, color is not to spec (no biggy) and
> slightly mis-registered (S/M runs on to lands). Our wireless group
> forwarded the PCB's back to the vendor to have the soldermask
> stripped. I was furious when I found this out, due to past
> experiences. Should I still be catious or has soldermask stripping
> tremendously improved.
>
> John Gulley - Process Quality Engineer
> Inet Inc
> 1255 W. 15th St.
> Plano, TX 75075-7270
>
>
>______________________________ Reply Separator
_________________________________
>Subject: RE: LPISM Stripping
>Author: "Bob Oliver; Jr." <[log in to unmask]> at Internet
>Date: 5/28/97 10:31 AM
>
>
>
>-----Original Message-----
>From: Anil K Singh [SMTP:[log in to unmask]]
>Sent: Saturday, May 17, 1997 11:21 AM
>To: TechNet
>Subject: LPISM Stripping
>
>We are using Coates LPISM could anyone suggest a good formulation for
>stripping cured LPISM boards.
>
>Thanks in advance
>
>Anil K Singh
>Linaks Microelectronics Ltd, India
>Fax:+91-522-222061, 315978
>
>***************************************************************************
>
>
>
>
--------------------------------------------------
Annie Laberge
--------------------------------------------------
Ingenieure Qualite
Matrox Electronic Systems (MES)
Tel: (514) 685-7230 ext 2933
Fax: (514) 685-3415
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To subscribe/unsubscribe send a message <to: [log in to unmask]> *
* with <subject: subscribe/unsubscribe> and no text in the body. *
***************************************************************************
* If you are having a problem with the IPC TechNet forum please contact *
* Dmitriy Sklyar at 847-509-9700 ext. 311 or email at [log in to unmask] *
***************************************************************************
============== End part 2 ============================
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To subscribe/unsubscribe send a message <to: [log in to unmask]> *
* with <subject: subscribe/unsubscribe> and no text in the body. *
***************************************************************************
* If you are having a problem with the IPC TechNet forum please contact *
* Dmitriy Sklyar at 847-509-9700 ext. 311 or email at [log in to unmask] *
***************************************************************************
|
|
|