Received: |
by ipc.org (Smail3.1.28.1 #2)
id m0vl2wA-0000XhC; Thu, 16 Jan 97 19:17 CST |
Content-Type: |
text/plain; charset=us-ascii |
From [log in to unmask] Fri Jan 17 09: |
31:02 1997 |
Date: |
Thu, 16 Jan 1997 16:46:40 -0800 |
Precedence: |
list |
Reply-To: |
|
Resent-Sender: |
|
Content-Transfer-Encoding: |
7Bit |
Status: |
O |
X-Mailing-List: |
|
X-Status: |
|
X-Loop: |
|
X-BeyondMail-Priority: |
1 |
TO: |
|
Resent-From: |
|
Return-Path: |
<TechNet-request> |
MIME-Version: |
1.0 |
X-Receipt-From-Agent: |
true |
Conversation-Id: |
|
Cc: |
|
Resent-Message-ID: |
<"t5UeN1.0.peF.pCjto"@ipc> |
Subject: |
|
From: |
|
Old-Return-Path: |
|
In-Reply-To: |
|
X-Mailer: |
BeyondMail for Windows/Professional 2.3 |
Message-Id: |
|
Parts/Attachments: |
|
|
Pratap, immersion tin coatings will loss their solderability in less than 24
hours. You may be able to use very aggressive fluxes and solder to immersion
tin coatings after 2 weeks, but I would be worried about ionic contamination.
If you are using an active flux anyway, consider using OSP coatings like Entech
106A or just "Bare Copper" instead of immersion tin. I use immersion tin to
cover bare copper for cosmetic purposes only.
The problem with immersion tin is that there is no solder to protect the
copper/tin intermetallic. The IMC layer oxidizes very quickly and is difficult
to reactivate.
In my experience the immersion tin/lead isn't much better than immersion tin.
However, if you can plate it thick enough (>0.0003") and reflow it immediately,
it works fine. After reflow the tin/lead surface should be bright and shinny
not matt gray.
Hope this helps.
Regards,
Jim Reed, Texas Instruments, Austin, TX
Voice = 512 250-7172,
Fax = 512 250-7967,
Email = [log in to unmask]
Pager = 800-759-8888 ID 289-7077
------------------
Original text
From: Pratap Singh <[log in to unmask]>, on 1/16/97 11:35 AM:
sam mccorkel wrote:
>
> I'm looking for any cautions or advice you may have on the following.
> We are considering the use of immersion tin as a finish on bare printed
> circuit boards.
> The boards are thru-hole only and they will be wave soldered within the next
> 3-4 weeks.
> Do you consider this a "no no" or is this an acceptable finish until wave
> soldering?
>
> ***************************************************************************
> * TechNet mail list is provided as a service by IPC using SmartList v3.05 *
> ***************************************************************************
> * To unsubscribe from this list at any time, send a message to: *
> * [log in to unmask] with <subject: unsubscribe> and no text. *
> ***************************************************************************
> * If you are having a problem with the IPC TechNet forum please contact *
> * Dmitriy Sklyar at 847-509-9700 ext. 311 or email at [log in to unmask] *
> ***************************************************************************
Do not use TIN coatings on PCB. Have you not read about Tin-Whisker
growth on tin coated boards that cause random short failures.
This mechanism has ben documented in several papers. Recently, a few
emails have beeen posted about the same mechanism.
--
Pratap Singh
Tel./Fax: 512-255-6820
e-mail: [log in to unmask]
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To unsubscribe from this list at any time, send a message to: *
* [log in to unmask] with <subject: unsubscribe> and no text. *
***************************************************************************
* If you are having a problem with the IPC TechNet forum please contact *
* Dmitriy Sklyar at 847-509-9700 ext. 311 or email at [log in to unmask] *
***************************************************************************
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To unsubscribe from this list at any time, send a message to: *
* [log in to unmask] with <subject: unsubscribe> and no text. *
***************************************************************************
* If you are having a problem with the IPC TechNet forum please contact *
* Dmitriy Sklyar at 847-509-9700 ext. 311 or email at [log in to unmask] *
***************************************************************************
|
|
|